A two-legged magnetic core with an air gap is shown in figure below. The depth of the core is 5 cm, the length of the air gap in the core is 0.07 cm, and the number of turns on the coil is 500. The magnetization curve of the core material is shown next to it. Assume a 5 percent increase in effective air-gap area to account for fringing. How much current is required to produce an air-gap flux density of 0.5 T? What are the flux densities of the four sides of the core at that current? What is the total flux present in the air gap? 10 cm 1.25 1.00

A two-legged magnetic core with an air gap is shown in figure below. The depth of the core is 5 cm, the length of the air gap in the core is 0.07 cm, and the number of turns on the coil is 500. The magnetization curve of the core material is shown next to it. Assume a 5 percent increase in effective air-gap area to account for fringing. How much current is required to produce an air-gap flux density of 0.5 T? What are the flux densities of the four sides of the core at that current? What is the total flux present in the air gap? 10 cm 1.25 1.00

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. If the material is the ideal material, N1I1 = 200, NIA = 100 and NIB = 150 If I am ampersand, what is the flux density in the middle of the air gap? okay? Calculate by drawing the magnetic circuit. b. If the material is not the ideal material (µr), the core material of each winding Find the inductance in terms of parameters c. What is mutual inductance between windings? D. Check the magnetic equivalent circuit of this system that there are no leakage fluxes. draw assuming. New magnetic with leakage fluxes in mind How about a circuit, draw?
A ferromagnetic core with a relative permeability of 1500 is shown in the following figure. The depth of the core is 5 cm. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 300 turns in the coil wrapped around the center leg of the core, and if the current in the coil is 1.25 A, find the magnetic flux and the field density in all three legs of the core, as well as the magnetic flux and flux density in the two air gaps.
For the circuit shown in Figure:a. Determine the reluctance values and show themagnetic circuit, assuming that μ = 3,000μ0.b. Determine the inductance of the device.c. The inductance of the device can be modified bycutting an air gap in the magnetic structure. If a gapof 0.1 mm is cut in the arm of length l3, what is thenew value of inductance?d. As the gap is increased in size (length), what is thelimiting value of inductance? Neglect leakage fluxand fringing effects.
The magnetic circuit shown in Figure P13.11 hastwo parallel paths. Find the flux and flux density ineach leg of the magnetic circuit. Neglect fringing at theair gaps and any leakage fields. N = 1,000 turns,i = 0.2A, lg1 = 0.02 cm, and lg2 = 0.04 cm. Assumethe reluctance of the magnetic core to benegligible.
The saturation curve of a particular core material shows that at a magnetic field intensity of 1250 At/m and the flux density is 0.80 Tesla. Determine the relative permeability of the core material.
To a magnetic core, with a relative permeability of 2100, a current I1 of 1 A and a current I2 of 2 A are applied, where the number of turns of the winding is 1000. The depth of the magnetic core is 20 cm. take into account that the bounded measurements are given in centimeters. The air gap shown in the figure is 0.2 cm and has an effective area equivalent to 1.1 times the cross-sectional area of the core. Determine:a) The equivalent circuit with sources and reluctance (Graph it)b) The magnetic flux of the central columnc) Magnetic induction at point Ad) Explain what would happen if the flow of current I1 is reversed
2nd - What does induction loading mean? a) friction load B) load with effect NS) loading by contact D) charge by electric field TO) charge with magnetic field
Using the magnetizing characteristics for samarium cobalt given in below figure,a) find maximum energy product and the corresponding flux density and magnetic fieldintensity. b) find the minimum magnet volume required to achieve an air-gap flux density of 0.8 Twhile ?? = 2 ??2 by the following figure,
State Ampere's circuital law. Hence find the expression for the magnetic field strength ( B ) of a long current carrying solenoid.
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a fluxdensity 3 T, the corresponding relative permeability of iron core is 1500. Determine thenumber of turns in the winding, given that the magnetic flux path has a mean length of 20cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2
The magnetic structure shown in the figure is built with a material whose magnetization curve is expressed by: (See image with the equation) The length of the mean magnetic path in the core is equal to 0.75 m. The measurements of the cross section are 6 × 8 cm 2. The length of the air gap is 2 mm and the flux in it is equal to 4 mWb (in the direction indicated in the Figure). Determine the number of turns in coil B. Ans: NB =1,237 turns (I need the procedure)
Given a magnetic circuit with a current 2.6A flowing through 205 turns of wire on a core having a reluctance of 125000 At/Wb. Determine the magnetomotive force of the circuit in base units.