A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm?, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A= 1000 mm Ee70 GPa >P=90 kN Copper L=2.0m A-550 mun E-120 GPa

A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm?, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A= 1000 mm Ee70 GPa >P=90 kN Copper L=2.0m A-550 mun E-120 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b. Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
Two 10-in 15.3-lb channels are welded together as shown in the figure. Compute the value of ?? ̅. (Answer is: Ix = 116.5 in4 )
Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on each bolt (MPa)
The aluminum rod AB (G=27 ???) is bonded to the brass rod BD (? =39 ???). Portion CD of the brass rod is hollow and has an inner diameter of 40 mm. Determine (a) the angle of twist at B. (b) the angle of twist in A
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
d. Calculate "P" in KN considering failure on shear on rivets Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
please sir solve accurate and fast. ( of possible solve compyuterised) THANKS a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when supported throughout under a tension of 5kg. the modulus of elasticity is 2.1x10^6kg/cm. what tension is required to make the tape measure 30m when supposed only at the two ends?
The steel and aluminum plate assembly is bolted together and fastened to the wall. Each plate has a constant width in the z direction of 200 mm and thickness of 20 mm. If the density of A and B is ρs = 7.85 Mg/m3, and for C,ρal = 2.71 Mg/m3, determine the location x̄ of the center of mass. Neglect the size of the bolts.