A two-stage compressor with a capacity of 1000 dm compresses 100 cu ft of free air per minute to a pressure of 100 psi. What is the required bhp? A. 4 B. 14 C. 8 D. 18 25.b. A centrifugal fan running at 100 rpm delivers air at the rate of 6000 dm at a pressure o

Q: 4.123 A rigid, insulated tank having a volume of 40 ft° initially contains a two-phase liquid-vapor ...

A:

Q: A jet of water 10 cm diameter strikes on a flat plate with a velocity of 18 m/s. The plate is moving...

A: We know that a jet of water with a diameter of 10 cm hits a flat plate at a speed of 18 m/s. We need...

Q: The lawn sprinkler shown in the figure rotates in the horizontal plane. A water flow of 15 L/min of ...

A: Find the torque and angular speed of the sprinkle. Given data :- Flow rate in = 15 L /min  

Q: An ammonia refrigerating system has a load of 250 kW and operates at a condensing pressure of 1400 k...

A: Using thermodynamic property table of ammonia, Enthalpy at various points are calculated using linea...

Q: If a rectangular duct system (12 inch × 26 inch) has an average velocity of 700 fpm, what is the air...

A:

Q: 10.13 Assuming that the compression process takes place through infinitesimal stages, calculate the ...

A:

Q: Find the moment of each of the forces shown in (Fig.1) about point o. I Find the total moment about ...

A:

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

A: Given that, PH=35 bar,PL=0.4 bar, From the steam table, At P=35 bar,TH=242.5 °C,At P=0.4 bar,TL=75.8...

Q: A steel hoop. 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm. 5. Is neated and shrunk on...

A:

Q: 1. Where necessary, assume air as an ideal gas and consider R = 287 J/(keK), Cp = 1005 J/(keK). QY= ...

A: Given dataMass flow rate = m˙ = 50 kg/sPressure at inlet = Pi = 500 kPa Temperature at inlet = Ti = ...

Q: The above left drawing shows a countershaft with helical gear B, bevel gear D, and two supporting be...

A:

Q: The system in the figure is in equilibrium. A concrete block of mass 230 kg hangs from the end of th...

A:

Q: 1. Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine th...

A: Find the maximum permissible value of torque

Q: Determine the maximum tensile stress (MPa) at

A: Determine maximum tensile stress.

Q: A turbine is supplied with 0.6 m³/s of water from a 0.3m diameter pipe; the discharge pipe has a 0.4...

A:

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is subj...

A:

Q: An A/C plant is designed for a room with the following conditions: outdoor conditions 40 F db / 60% ...

A: Given: The outdoor temperature, Tdb1 = 40 F = 4.44°C The outdoor RH, ϕ1 = 60% The indoor temperature...

Q: 40 kN E 2 m B F 3 m 50

A: to find reaction component at B and C

Q: If Q = 450 N and support reaction P, = 300 N, determine the force magnitude in member CJ. !3! 1m 1m ...

A: Find the magnitude of force in member Cj Where  Q = 450 N               Py = 300 N

Q: 2. Detemine the elongation of the tapered cylindrical aluminum bar caus the 30-kN axial load. Use E ...

A: P=30kN L=400mm D1=20mm D2=30mm E=72GPa

Q: Situation - The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short pos...

A: Find the required values Given data:- Length = 5 m h = 0.9 m Diameter of cable = 8 mm

Q: Find the time required for one full cut on a work piece of 350mm long and 20 mm in diameter. The cu...

A:

Q: 2. Determine the force in each member of the truss shown. B 12' 9 E 9'- -9'- -9'- 300 lb 300 lb 900 ...

A:     From equilibrium conditions  

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

A: GIVEN DATA- A CARNOT VAPOUR CYCLE WORKING BETWEEN 4bar AND 0.4bar we have to find heat added to boi...

Q: terminal velocity V

A: Given: A solid block of 2 kg mass slides steadily at a velocity V along a vertical wall as shown in ...

Q: Steam at 1.2 MPa and 500 C undergoes isentropic ( S=C ) expansion process. For mass flow of 2.5 kg/s...

A:

Q: The motion of a particle is governed by the relation a = 4t^2, where a is in ft/^s2 and t is in seco...

A:

Q: 2.30 Determine the moment of the force Fabout point A in terms of Fand d. Use (a) the scalar method;...

A:

Q: Q6: The following force of mortality is given: Hy = 0.02 + - for 0sys 100. 100-y' 200-y Find 10918:

A: It is given that, μy=0.02+1100-y+2200-y for 0≤y≤100 10q10 needs to be calculated in this problem.  

Q: m.K carries a fluid at 200°C, with a convection heat transfer coefficient of 210 W/m2./K. The tube h...

A:

Q: A block of mass m = 16 kg oscillates attached to a spring of spring constant K = 162 N/m. The motion...

A:

Q: maving a cross-sectional area of 300 mm and a length ly from one end. The rod supports a tensile loa...

A:

Q: .........TheGaugePressure 0f the air in an aut0m0bile tire is 25psi, and assuming the ambient atm0sp...

A:

Q: Q.2) If P = 160 N. Determine the moments of P about (a) point O; and (b) point C. 600 mm 360 mm

A:

Q: A particle is moving along a circular path of radius 300 mm. If its angular velocity is 0= (21²) rad...

A: Given data Radius = r = 300 mm Angular Velocity = θ˙ = 2t2 rad/sIt is required to find the particle ...

Q: Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 7...

A:

Q: Draw the FBD of member ADB 20 lb 15 in. 15 in.- A C В D

A: FBD:   Let RC be the reaction force at point C. Let XB and YB are the horizontal and vertical react...

Q: The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through i...

A:

Q: An elastic string of natural length 4l and modulus of elasticity 4mg is stretched between two points...

A:

Q: A jet of water from a fixed nozzle has a diameter of 25 mm and strikes a flat plate at an angle of 3...

A: We know that a fixed nozzle's water jet has a diameter of 25 mm and impacts a flat plate at a 30o an...

Q: A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Eb = 14,000 ksi)and weight...

A: Modulus of elasticity of copper rod,Ec=12000ksiModulus of elasticity of brass rod,Eb=14000ksiLoad=W=...

Q: How is thermal energy lost when a person exits a building through an exterior door in the winter? a)...

A:    Convection is the transfer of heat from one section of a fluid (liquid or gas) to another by the ...

Q: Three kg of steam at 121°C and 10%moisture undergoes a constant  volume process until the pressure ...

A:

Q: 1. Moist air has a dry bulb temperature of 110 F and a wet bulb temperature of 87 F. The air is at a...

A:

Q: A cylindrical wire which has a starting diameter of 5 mm is deformed two times to make a finer (smal...

A: Given : D = 5mm 20% reduction in area for each deformation To find : Total effective strain

Q: The ball at A is kicked such that 0A = 57 •. It strikes the ground at B having coordinates x = 15 ft...

A: Find the velocity of ball at kicked and strike the ground

Q: Draw a sound conclusion based on how you familiarized the key components of the lathe machine. Empha...

A: Lathe machine: The main objective of this machine is to remove the extra material by rotating the wo...

Q: s A & B SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer(s) and label them

A: Given:Diameter of pipe, d1=100 mmradius of pipe, r1=50 mmwall temperature of pipe, T1=-10o CThicknes...

Q: 6.21. The owner of the dump in Problem 6.20 suggests things would be much better if a 20-m stack wer...

A: Given DataFrom above question we had getemission without stack=284μg/m3QNOx=3g/sH=20m

Q: The cross-sectional area of each member of the truss is 42 cm2. в L. C E 6m 100 kN 300 kN Determine ...

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.