A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.) 3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5° and angle of contact of belt with the pulley is 160°. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.

Given that, Speed of belt, N=1440 m/min,Coefficient of friction between belt and pulley, μ=0.3,Angle…

A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. If the mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power. (Consider the centrifugal tension in the belt.)

A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. If the mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power. (Consider the centrifugal tension in the belt.)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5o and angle of contact of belt with the pulley is 160o. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.
A pile-driver hammer has a mass of 300 kg and is to be raised 16 m in 4 sec. The total friction on the guides is constant at 400 N. What constant pull must be exerted on the cable?
A bicycle and rider, travelling at 12 km/hr on a level road, have a mass of 105 kg. A brake is applied to the rear wheel, which is 800 mm in diameter. The pressure force on the brake is 80 N and the coefficient of friction is 0.06. Find the distance covered by the bicycle and the number of turns of its wheel before coming to rest.
A force of 200 N is exerted on a snack box of 5 kg still on the floor. If the coefficient of friction is 0.3, calculate the static friction.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
5. A box with a mass of 100 kg was originally attached to the spring at position A. After that, pressure was applied to the box until The spring compresses to a distance of X - 1 m and releases it, causing the box to move upwards along the inclined floor. If the incline has and = the coefficient of friction uk = 0.3, find the box that can travel along the incline for a maximum distance in meters.
Two identical pulleys with diameter of 711 mm, are mounted on two parallel shafts for flat belt drive system. The maximum permissible tension in the belt is 2,691 N and the coefficient of friction between belt and pulley is 0.31. The centrifugal tension acting on the belt is 887 N. Calculate the power that can be transferred in Watts if the rotational speed of the driving pulley is 978 r.p.m.
A large box of mass m sits on a horizontal floor. You attach a lightweight rope to this box, hold the rope at an angle u above the horizontal, and pull. You find that the minimum tension you can apply to the rope in order to make the box start moving is Tmin. Find the coefficient of static friction between the floor and the box.
The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm and a speed of 1420 rev/min. The coefficient of friction between the belt and the pulley is 0·4 and the angle of lap is 160°. (a) Calculate the tension in each side of the belt at operating speed. (b) Determine the power transmitted when the belt is on the point of slipping. If the pulley system uses a flat belt of CSA 500 mm² and density 1300 kg/m3, determine: (c) The power transmitted, when the mass of the belt is taken into consideration.