A V-notch weir is located (or cut) at one end of a tank having a horizontal square section 15m (L) by 12m (W). If the initial head on the weir is 1.50m (H) and it takes 250 seconds to discharge 165 cu.m. of water, what could have been the vertex angle of the weir? (Use a correction factor, C' = 0.70) AKI

A V-notch weir is located (or cut) at one end of a tank having a horizontal square section 15m (L) by 12m (W). If the initial head on the weir is 1.50m (H) and it takes 250 seconds to discharge 165 cu.m. of water, what could have been the vertex angle of the weir? (Use a correction factor, C' = 0.70) AKI

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a trapezoidal weir with a side slope of 1H to 2.8V allows a flow rate of 51m^3/s Assuming a constant depth of 2.3m above the crest, what is the length (m) of the weir? c=0.6
P2) If using a V-notch weir in 2.83m rectangular channel.The height of crest installed at 0.85m above the bed. For head=0.935m, and the tailwater= 1.44m, find the discharge.
Trapezoidal weir has a lower base of 3 m and has an angle of 45 for the inclined side. The initial head of the weir is 5 m. Find the discharge if the coefficient of the whole weir is 0.042. a. 8.604 m³/sec b. 9.969 m³/sec c. 10.36 m³/sec d. 5.712 m³/sec
A suppressed weir 7.5m long is to discharge 10.125 m3/s of water onto an open channel. The weir factor Cw = 1.88. To what height P may the weir be built, if the water behind the weir must not exceed 1.80m deep?
A trapezoidal weir of length 4 m and sides inclined 1 horizontal to 1.5 vertical discharges 12 m³/s. If the discharge coefficient is 0.65, find the head of the weir.
Determine the head on a 45° V-notch weir for a discharge of 200 L/s. Use C=0.57.
Find the width, in meters, of the channel at the back of a suppressed weir using the following data: Head, H = 30 cm Depth of water, d = 3 m Discharge, Q = 0.84 cubic meter/sec Consider velocity of approach and use Francis formula.
The length of the crest of a trapezoidal weir is 2m. the sides are sloping at 75 degrees 57' 49" with the horizontal, if the head on the weir is 0.5 m, 1. Prove if it is a Cipolleti weir or not 2. Find the discharge in cu. m/s
Determine the vertex angle (in deg.) of a V-notch weir for a discharge of 29,762 L/s and a head of 4.49 m. Use Cd = 0.942. Round off to two decimal places.
A trapezoidal weir having side slopes of 4:5 (Horizontal to Vertical) and 1:1 (Horizontal to Vertical), respectively, is to have a theoretical rate of discharge of 2.0 cubic meters per second when the head on the crest is 0.60 m. Find the length of the crest using integration (principle of orifice).
1. Find the width of the channel at the back of a suppressed weir using following data H = 18.5cm , d = 2.485m , Q = 0.84 m^3/s. Consider the velocity of approach and use Francis Formula. 2. a sharp-crested triangular weir with weir angle 80 degrees carries water under a head of 0.955m .find the flow over the weir.
The head over a ?rpezoidal-crested weir, whose breadth is 5m, is 4m. Given that discharge coefficient is 1.8, calculate the discharge over the weir.