The water content of a saturated soil and the specific gravity of soil solids were found to be 30% and 2.70, respectively. Assuming the unit weight of water to be 10 kN/m³, the saturated unit weight (kN/m³) and the void ratio of the soil are

The water content of a saturated soil and the specific gravity of soil solids were found to be 30% and 2.70, respectively. Assuming the unit weight of water to be 10 kN/m³, the saturated unit weight (kN/m³) and the void ratio of the soil are

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Weight-volume Relationships And Plasticity

Section: Chapter Questions

Problem 3.5P

See similar textbooks

Related questions

Q: An orifice has a coefficient of discharge of 0.62 and a coefficient of contraction of 0.63.…

Q: Determine maximum shear stress if maximum principal stress is 10 Mpa and minimum principal stress is…

A: Given data : The value of maximum principal stress σ1=10 MPa The value of minimum principal stress…

Q: An orifice has a coefficient of discharge of 0.62 and a coefficient of contraction of 0.63.…

A: Given data : The value of coefficient of contraction CC=0.63 The value of coefficient of discharge…

Q: In a building construction site, temporary structures and connections are needed. Identify the…

A: Temporary structures and connections are made during building construction to facilitate the…

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how…

Q: A balloon-type apparatus is used to determine an in-place unit weight for a soil(Field Density…

A: Given : Volume of soil, V = Volume of the test hole = 0.025 ft3Weight of soil obtained from the test…

Q: In triangle ABC, b = 17, c = 28, and A = 91°. Find a. O 31 32 33 34 Other: O

Q: max moment

Q: 454 For Problems 20.17 through 20.20, use the matrix approach to solve fo the member end forces. In…

Q: 9.30 A laminar boundary layer velocity profile is approximated by the two straight-line segments…

A: For calculating Boundary layer thickness ; δ = 2C2vxUC1 where ; C1 =∫01g(1-g)dY C2 = dgdY

Q: Problem! 4 Provide the liquid limit, LL = 75; the plastic limit, PL = 45%. The water content the…

A: L.L = 75 PL = 45 wL (water content) = 50 PI (Plasticity Index) = LL - PL = 75 - 45 = 30 Here, LL…

Q: shown, calculate the initial tension induced in each cable immediately after release ngular…

A: Given Data -

Q: Answer: (b)x= (c) Vmax = L E mm Wo B X

Q: Need help asap. can you correct all the calculations like the integration part, can you make it a…

A: Solution-The given values are as follows,d1=20cm or 0.20md2=20cm or 0.20mC=0.80To Determine,T=?

Q: The block slides down an incline. It starts from rest and, after moving 6 ft, strikes a spring (k-…

A: The values and figure given in the question are as follows: Spring stiffness coefficient(k)=100…

Q: Determine void ratio of soil

A: Given data : The value of moisture content w=12100=0.12 The value of porosity of soil n=0.4 The…

Q: Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a…

Q: 3-1. The members of a truss are pin connected at joint O. Determine the magnitudes of F, and F₂ for…

A: A system of forces is given and it has been asked to determine resultant of the same. Please refer…

Q: 5/22 Determine the x- and y-coordinates of the centroid of the shaded area. a 1 | y=k₂√x y=k₁x³…

Q: sample has a total mass of 23.3 g a volume of 12 cm³, an oven-dry mass of 21.2 g, and a specific…

Q: a) Determine the vertical reaction at support A. 8 k/ft 4 k/ft .…………. A B 30 ft

Q: nd the value of strain if stre O MPa

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A: Load will be P in each road.

Q: 1. Determination 2. Determination of Normal Consistency Of Hydraulic Cement of Setting Time of…

A: 1) Normal consistency of hydraulic cement as defined as, The Consistency of cement test is performed…

Q: Determine the live load that the beam can carry based on the mome

Q: Find the kinematic viscosity of a liquid if you're given, Specific gravity = 1.4 Viscosity = 0.0040

A: Kinematic velocity is ratio of dynamic viscosity and density.

Q: 4. Determine the maximum factored load w₁ that the beam can carry based on the ultimate shear…

Q: 2. Healthy Harry's Juice Bar has the following cost schedule (in tk.): Q(Quantity) Variable Cost…

A: Given data,

Q: F₁=54N 4 60° F₂ = 60N

Q: 20. A trapezoidal canal, 6m at the bottom and having side slopes 2:1 carries water to a depth of…

A: B = 6m Side slope 2:1 = n:1 ---> n = 2 V = 0.6 m/s

Q: Analyse the rectangular two way slab for the yield pattern -1 (as shown below) by Equilibrium…

Q: A 1.7m simply supported timber floor joist with b=25mm and d=175mm with bridgings at third points…

A: Bending equation can be written as ; MI=σy σ = M yI Where ; M = wL28 = 36 (1.7)28=13 KN-m I = bd312…

Q: y supported beam shown consists of a W410 × 60 structural steel wide-flange shape [E = 200 GPa; I =…

A: Given data E = 200 GPa = 2 × 105 N/mm2 I = 216 × 106 mm4

Q: +Tabulated Data and Result, Modulus of Rupture Sample No. L (mm) b (mm) h (mm) 1 730 50 50 2 730 50…

Q: 9.23 It is relatively easy to design an efficient nozzle to accelerate a fluid. Conversely, it is…

A: There are following difference in acceleration of fluid in nozzle and retardation of fluid in…

Q: In the Hirakud hydroelectric power station, there are four Kaplan and two Francis turbines,…

A: Given: The average head is 26.5 m. The overall efficiency of the Kaplan turbine is 90%. The overall…

Q: Determine the slope at point B and deflection at point D

Q: 2

A: Here they have calculated for each orifice. As the tank has two orifices divided by 2 gives for each…

Q: Dimension the following objects 2. POWER SURGER PROTECTOR CASE SCALE: 1:2 NAME: SECTION:…

A: Dimension of the object Here, r is the radius of fillet, a is the width of the object b is the…

Q: A vertical steel rod is fixed at top and supports an 8-kN load at the lower end. The rod is 10mm in…

Q: SITUATION 1 Building Data: #suspended floors 5 Floor Level 5 4 3 2 Height Dead Load (kN) (m) 3.1…

Q: 9.14 If the upstream velocity of the flow in Problem 9.13 is U = 1.5 m/s, determine the kinematic…

A: NOTE - As per BartleBy policy Experts are only allow to answer single question at a time So, please…

Q: vehicle time headway is 2.5 sec/vehicle and the spacing of cars measured at a point along the North…

Q: Determine the value of friction if normal force is 1200 N and coefficient of friction is 0.462

A: Given data : The value of coefficient of friction μ=0.462 The value of normal force N'=1200 N To…

Q: 9.22 An atmospheric boundary layer is formed when the wind blows over the earth's surface.…

Q: 9.30 A laminar boundary layer velocity profile is approximated by the two straight-line segments…

Q: I. Design a reinforced concrete beam to carry a service dead load of 15kN/m ( including its own…

A: Answer Service dead load DL = 15 KN/m Service live load LL = 120 KN Beam span L = 6 m f'c = 28 Mpa…

Q: At a temperature of 60°F, a 0.02-in. gap exists between the ends of the two bars shown. Bar (1) is…

A: Lowest Contact Temperature Before the gap is closed, only thermal strains and the associated axial…

Q: Which type of symmetry is impossible to exist in a finite design?

A: This question has been taken from engineering drawing

Q: Determine the maximum and concrete and steel stresses at the point of maximum positive and negative…

Concept explainers

Weight-Volume relationships

Weight is defined as the quantity of matter contained in a body. Weight can also be defined as the force acting on a body due to gravity. Mathematically, weight can be defined as-

Question

The water content of a saturated soil and the
specific gravity of soil solids were found to be
30% and 2.70, respectively. Assuming the unit
weight of water to be 10 kN/m³, the saturated
unit weight (kN/m³) and the void ratio of the soil
are

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The water content of a saturated soil and the specific gravity of soil solids were found to be 25% and 2.65 respectively. Assuming the unit weight of water to be 11KN/m³, the saturated unit weight (KN/m³) and the void ratio of the soil are respectively:
A soil has a dry density of 1600 kg/cu.m and a void ratio of 0.63. Compute the saturated density of the soil.
The void ratio of a soil is 1.2. Determine the bulk and effective unit weights at, first 75%, second 95%, and 100% saturation. What is the percentage error in the bulk unit weight if the soil is 95% saturated but assumed to be 100% saturated?
For a soil specimen, the following soil properties are known: saturated unit weight γ = 19.1 kN/m , void ratio e = 0.45. What is the dry unit weight of the specimen? Assume unit weight of water γ = 10 kN/m3
In an undisturbed soil formation, it is known that the dry unit weight is 18.06 kN/m3. The specific gravity of the soil particles is 2.75. (a) What is the saturated wet unit weight of the soil, in kN/m3 and pcf? (b) What is the submerged effective weight of the soil, in kN/m3 and pcf? (c) What is the submerged effective density (Mg/m3)?
For a moist soil specimen, the following are given Gs= 2.67, volume = 0.5 m³ moist unit weight = 9.5 KN and the moisture content = 7.3%. Determine Dry unit weight, Void ratio, porosity, Degree of saturation.
The bulk unit weight of the soil is 16.680 kN/m3 at a saturation of 36.870 % and the effective unit weight is 9.580 kN/m3. If the maximum and minimum void ratio of the soil is 0.880 and 0.390, respectively, determine the following: max dry unit weight , relative density , saturated unit weight
Given the void ratio of a soil is 0.85. What is the percentage error of the bulk unit weight if the soil were 95% saturated and assumed to be totally saturated?
For a given soil, the following are known. Gs=2.74,moist unit weight = 20.6 KN/cu.m, and moisturecontent is 16.6%.a) Determine the dry unit weightb) Determine the void ratioc) Determine the porosityd) Determine the degree of saturatione) Determine the weight of water in KN to beadded per cubic meter of soil for a 100%degree of saturation.
A natural deposit of soil was found to have a water content of 27% and to be 88% saturated. Gs=2.7.Calculate (a) the void ratio, e; (b) the porosity, n; and (c) the dry density, ρd. (use kg/m^3 for density units). Include phase diagrams.
A saturated soil specimen has w = 36% and ᵞd = 85.43 lb/ft3. Determine: Porosity
2. A saturated soil with specific gravity of solids equal to 2.65 has a unit weight of 19KN /m^3. Determine the dry unit weight (KN/m^3) and porosity of the soil sample.