A vehicle of weight 40 kN negotiating a horizontal curve of radius 250 m is subjected tothe friction force of 5 kN. The distance between the wheels of the axle is 0.8 m and heightof CG of vehicle from road surface is 0.6 m. Determine the maximum speed of vehiclepermitted so that overturning and sliding can be prevented.

Answered: Image /qna-images/answer/28faa85e-e802-4187-829c-65c68ffa6a2e.jpg

Answered: A vehicle of weight 40 kN negotiating a…

A vehicle of weight 40 kN negotiating a horizontal curve of radius 250 m is subjected to the friction force of 5 kN. The distance between the wheels of the axle is 0.8 m and height

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the maximum speed of train on a broad gauge high speed 4° track. Assume 1 chain length = 2...

Q: rigid pavement is to be used to carry a wheel load of 50.93 kN. Enough dowels will be used across th...

Q: Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1) ...

Q: The support reactions for the following frame, if g = 2 kN/m are 2 KN Ax = - kN rightward Ay = - kN ...

A: Given -

Q: A 9.2-kg plastic tank that has a volume of 3.3 m3 is filled with liquid water. Assuming the density ...

Q: Usa o-7 ft, b- 11 ft,c-5 ft, and w- 9 kips/ft. The reaction forces for this beam are A,- 45.2 kips a...

Q: The trapezoidal channel shown in figure is laid on a slope of 0.00191. the channel must carry 60 cfs...

Q: Given a system as shown in the following figure. Calculate the water level difference between two ta...

A: Solution- The given values are as follows,Taking tannk (1) is the upper tank and tank (2) is lower ...

Q: An 8.8-kg slab slides down an 15° inclined plane on a 5.6-mm-thick film of oil with viscosity u(mu)=...

A: Given data, m = 8.8 kg θ = 15° t = 5.6 mm Contact area = 7 m² µ = 2.5 Pa.s To find out the terminal...

Q: A 19 inches square steel bearing plate lies between an 8 inches diameter wooden post and a concrete ...

Q: Determine the correct length of the line if 10:6

A: SURVEYING:

Q: Solve with Force Method and find T2

Q: If current ADTS of a highway is 24,000 and rate of annual growth in traffic is 3% for 18 years desig...

A: Factor projection factor=(1+r)n+x n=design life r= annual growth rate n=design life =18 x= construct...

Q: A 12m beam will be subjected to the following loads: Uniform dead load due to self weight - 25.8 kN/...

Q: s in oil (op.gr.=o.82) e water sarface

A: Given data- Specific gravity (SG) = 0.82 Head at point A = 2m Difference between level of tubes (x) ...

Q: Calculate the extra widening required for a single lane major district highway having horizontal rad...

Q: Calculate the minimum sight distance required on a two way two lane road for the two vehicles approa...

A: We will use formula of stopping sight distance .

Q: 10 kN /m A B 2 m 4 m 450 Determine the horizontal and vertical component of raction at che pins A,B....

A: To find reaction at A, B, C

Q: The line loads q1 = 200 KN/m and q2 = 500 KN/m are applied as shown, determine the A6z at point A at...

A: We will take vertical component of loading.

Q: Calculate the extra widening required for a single lane major district highway having horizontal rad...

A: 9e

Q: Find maximum principal stress

A: This question is related with solid mechanics . In this question we are provided with value of norma...

Q: . DATA AND RESULTS 1. OBSERVED DATA OBSERVED DISTANCE OBSERVED BEARING LATITUDE DEPARTURE LINE (m) (...

A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly r...

Q: A line was found out to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 ...

Q: Compute the peak hour factor if the hourly volume of traffic is 1964 veh/hour and the highest 15-min...

A: Compute the peak hour factor

Q: Question 11 A steel pipe 1.2 m in diameter is required to carry an internal pressure of 720 kPa. If ...

Q: e the moment-area method to determine the slope and deflection at point D of the beam shown.

A: Step: 1 Moment of area method: - It is a method to obtain bending displacements of structures like ...

Q: Solve the differential Equation. Please show complete solution.

A: DIFFERENTIAL EQUATIONS:

Q: Hinge it お 2L 3. (One redundant)

Q: (c) If the cross-section of the beam is the composite section shown below, determine the maximum str...

A: Assume constant moment 20kft. N=Es/Ec N=29000/2000=14.5 Transform the section in wood section

Q: Compute the peak hour factor if the hourly volume of traffic is 1829 veh/hour and the highest 15-min...

Q: A PCC pavement is designed with a base layer of 100,000 psi modulus and loss of support factor 1.0. ...

Q: A 5 cmx12 cmx6 m wooden plank (S.G.wood = 0.70) is required to stand vertically in water. To reduce ...

A: We have to determine the value of draft of the wooden plank and metacentric height of the whole syst...

Q: A road having a radius of 120m and has an angle of 9.31° from the horizontal. The center of gravity ...

Q: As a Civil Engineering students, what do you think is the importance of Engineering Drawing and know...

A: Engineering Drawing is important to civil students as civil students have to draft many structures a...

Q: Calculate the maximum speed of train on a broad gauge high speed 4° track. Assume 1 chain length = 2...

Q: 10 kN/m B 2 m 4 m 450 Determine the horizontal and vertical component of raction at the pins A,B.C

Q: Load-Shear and Shear-Moment Relationships Requirements 1A. Reactions at the supports 1B. Shear diagr...

A: RA + RC = 40 + 16X3 RA + RC = 88 Moment diagram 40 x 1 +15 - 16 x 3 x 4.5 + Rc x 5 =0 Rc = 32.2 k...

Q: Aload Pissupported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17400...

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rod...

Q: For the structure shown below calculate the tension force in the lateral resisting system. Assume a ...

A: Assuming there is a structure, there will be a frame in the construction more often than not. Outlin...

Q: w = 14 kN/m, ME 3 kNm, and RA = 7.92 kN w kN/m MẸ kNm в A B C D E 0.8m 1.0m 0.7m 2.0m RA M(x) cut

Q: Pick up the incorrect statements from the following: 1. Cast iron pipes are structurally stronger an...

A: Answer - 2. Sonocsope is used as replacement of venturimeter for discharge measurement. Explanation...

Q: quality management plan of Lrt eglinton midtown crossover construction project. 500 words

A: here is your answer below ;

Q: The probability in percent of a 150 year return period not to occur within the next 45 years is?

Q: In your own opinion, what is most likely the significant function of a Civil Engineer?

A: civil engineering, the profession of designing and executing structural works that serve the general...

Q: - For the sluice gate shown in figure, if C, = 0.98 and C. 0.62, what is the height of the opening? ...

Q: Determine the mass (kg) of the heaviest cylinder that can be supported without exceeding a stress of...

Q: ia plans to buy a house for Php 159889. She wants to make a down payment of Php 20111 and to take ou...

A: Actual cost of house = Php 159889 He make a down payment = Php 20111 Remaining Balance = 159889 - 2...

Q: A vehicle of weight 40 kN negotiating a horizontal curve of radius 250 m is subjected to the frictio...

Q: 5. A long footing 2 m wide is buried at a depth of 1 m. The groundwater table is expected to exist d...

Concept explainers

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.

Question

A vehicle of weight 40 kN negotiating a horizontal curve of radius 250 m is subjected to
the friction force of 5 kN. The distance between the wheels of the axle is 0.8 m and height
of CG of vehicle from road surface is 0.6 m. Determine the maximum speed of vehicle
permitted so that overturning and sliding can be prevented.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The radius of a highway curve is 120 m, and has an angle of 9.31° from the horizontal. The center of gravity of the car is located 0.80 m above the roadway and the distance between the two front wheels is 1.2 m. If the car has a total weight of 15 KN. a. Determine the normal acceleration and the velocity (in kph) of the car before overturning. b. Find the maximum velocity of the car could move along the curve so that there will be no outstanding pressure between the tires and the roadway. c. If the coefficient of kinetic friction is 0.60, what is the maximum velocity (in kph) of the car without sliding.
If the crest of the hill has a radius of curvature ρ = 345 ft, determine the maximum constant speed at which the car can travel over it without leaving the surface of the road. The car has a weight of 2700 lb. Neglect the size of the car.
For a car travelling with a speed of 50kph around a curve of radius 50m., Find the angle at which a road should be banked so that no friction is required.
The banking of the road way is 10 degrees at a radius of curvature of 80m, what will be the maximum velocity for a 2 ton vehicle and a 5 ton vehicle if the coefficient friction is 0.4 ?
The car has a mass of 1.6 Mg and center of mass at G. If the coefficient of static friction between the shoulder of the road and the tires is μs = 0.4, determine the greatest slope θ the shoulder can have without causing the car to slip or tip over if the car travels along the shoulder at constant velocity.
A truck weighing 35 tons is traveling at 32 km/h round a curve track of 43 m radius. If thecenter of gravity of the truck is 2.3 m above the rails, calculate the vertical reaction of eachwheel if the wheel distance is 1.7 m apart Additionally, if the track is banked at 13 degree and thecoefficient of friction is 0.4, and find the truck's maximum speed.
A car having a weight of 40kN 5 points is moving at a certain speed around the curve. Assuming no lateralpressure between the tire and pavement and considering a centrifugal ratio of 0.30, Compute the force in kN that will tend to pull the car away from the center of the curve. assume f = 1.0 for fatigue design.
The super elevation of the horizontal curve is 0.12 m/m. A car can travel a maximum speed of 80 kph. Find the coefficient of friction between the tire and the road if the radius is 70 m. a. 0.52 b. 0.62 c. 0.72 d. 0.42
A highway curve with a radius of 150 meters is banked so that there is no lateral pressure (friction) on the wheels of a car at a speed of 50 km/hr. A car weighing 16.50 KN with tread G = 1.50 meters and height h = 0.70 meters travels around the curve at 100 km/hr. What is the safe angle of inclination of the banked highway curve
The radius of a highway curve is 120m, and has an angle of 9.31° from the horizontal. The center of gravity of the car is located 0.80m above the roadway and the distance between the two front wheels is 1.2m. If the car has a total weight of 15KN, a. Determine the normal acceleration and the velocity (in kph) of the car before overturning? b. Find the maximum velocity of the car could move along the curve so that there will be no outstanding pressure between the tires and the roadway. c. If the coefficient of kinetic friction is 0.60, what is the maximum velocity (in kph) of the car without sliding?
A car requires 4m to stop after the application of brakes. Determine the speed of the car just before the brakes were applied. The road has a slope of -2.4% and average of coefficient of friction of 0.42.
A car travels at a costants speed of 100kph when its initial position is 400m measured horizontally and whose vertical terrain is given by the equation y=0.0003x^2. (A) Compute the radius of curvature at its initial position. (B) Find the total acceleration of the car if the position of the car is 200m from its initial position