A venturi meter, shown in the figure, has the geometric characteristics supplied below, m³ a volume flow rate of 0.01 of a fluid with density p 874 flows through it, the S kg differential manometer fluid is mercury with density 13,600 Find the height h of the manometer in meters. Assume acceleration of gravity 9.80 m³ m 8² D1 Diameter of section 1= 0.123 m D2 Diameter of section 2= 0.06 m h 1 2 J . Flow direction indicated by blue arrow

A venturi meter, shown in the figure, has the geometric characteristics supplied below, m³ a volume flow rate of 0.01 of a fluid with density p 874 flows through it, the S kg differential manometer fluid is mercury with density 13,600 Find the height h of the manometer in meters. Assume acceleration of gravity 9.80 m³ m 8² D1 Diameter of section 1= 0.123 m D2 Diameter of section 2= 0.06 m h 1 2 J . Flow direction indicated by blue arrow

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

Using the data given in the schematic attached, find the difference of pressure PA and PB h1= 0.65m h2= 0.1m h3= 0.75m h4= 0.45m Density of fluid A is pA= 900kg/m3 Density of fluid B is pB= 1034kg/m3 Mercury density is pHg= 13600kg/m3 Oil density is poil= 700kg/m3 (In the given figure, the pipelines are parallel to each other and not necessarily at the same height.)
Find the air horsepower of an industrial fan that delivers 40m3/s of air through a 700mm x 1000mm duct if static pressure is 150mm of water gage and air density is 1.18kg/m3 Answer: 182.2
A 6.0 cm diameter horizontal pipe gradually narrows to 4.5 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 33.5 kPa and 22.6 kPa, respectively. What is the volume rate of flow?
Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.
Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1 tapering to 3.40 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s(b) point 2 m/s
As can often be seen in a kitchen sink when the faucet isrunning, a high-speed channel fl ow ( V 1 , h 1 ) may “jump” toa low-speed, low-energy condition ( V 2 , h 2 ) as in Fig. . The pressure at sections 1 and 2 is approximately hydrostatic,and wall friction is negligible. Use the continuity andmomentum relations to fi nd h 2 and V 2 in terms of ( h 1 , V 1 ).
Unless stated otherwise take:Patm = 10^5, P(water) = 1000 kg/m^3 ; P(air) = 1.2 kg/m^3 ; g = 9.8m/s^2gage pressure Pg = P - PatmUnless specified otherwise assume uniform velocity profiles in duct locations.The Bernoulli eq’n (BE), P + ½ρV2 + ρgz = constant In this formulation the scalar variable z is the vertical height measured opposite the direction of g (z is always taken up independent of your coordinate system; pgz is potential energy)This BE is only valid along a streamline in steady state flow, when viscous friction effects can be ignored, called “ideal” fluid motion, and the density is assumed to be constantthe differential radial component of –?P + ρg = ρawith the centripetal acceleration , ar = - V^2/r , to get dp/dr = ρgr + ρV^2/rThe Bernoulli eq’n is often divided through by the constant ρg ≡ γ so that each term has units of length, a height or “head” : (P/ ρg) + (V2/2g) + (z) = constant. Q = VA = flow rate = constant, as a second eq’n to solve for an unknown velocity. the…
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
A certain axial flow turbine has an output torque M that isproportional to the volume flow rate Q and also depends onthe density ρ , rotor diameter D , and rotation rate Ω . Howdoes the torque change due to a doubling of ( a ) D and ( b ) Ω ?
Water enters a shower head through a pipe of internal radius r = 6.4 mm, and leaves through 30 small holes, each of radius r1 = 0.08 mm. When the faucet is opened, the water moves in the tube at a speed of 90 cm/s. What is the volumetric flow of the shower head in liters per second?
Torricelli problem. A tank whose shape is obtained by rotating y = x6. At t = 0, the water height is y = 2. The hole at the bottom is of area a = 0.05m2. The gravity acceleration is g = 9.8m/s2. How long will it take for all the water to drain from the tank?
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m