Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.

Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.

Name: Water is flowing in the pipe shown in the figure below, with the 8.20-
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, locatedy = 11.5 cmbelow point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume stead

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1 tapering to 3.40 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s(b) point 2 m/s
Consider coolant in a circular pipe to be in laminar flow; the following formula gives one-dimensional velocity: V=Vmax*(1-((r/R)^2)) Vmax = 2 m/s R = Radius of Pipe = 0.05 m Fluid Density (uniform) = 300 kg/m^3 1. What is the coolant flow (m^3/s)? 2. What is the coolant average velocity in the pipe (m/s)? 3. What is the true kinetic head of flow expression?
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
O.S. A vertical orifice is 10 cm. square and has an actual flow of 28 Ips with Cv=0.95, Cv = 0.62 as shown in the figure. If the liquid is oil (s.g. = 0.85), what is the head, h in meter over the orifice is required? In Problem 1, determine the theoretical velocity of the jet Also in Problem 1, determine the theoretical flow (Ips).
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe, the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B.
The pressure gage leading to the turbine casing of a Francis turbine reads 0.5 MPa and the center of the spiral casing is 5 m above the tailrace. What is the net head if the velocity of the water entering the turbine is 10 m/s?
O.S. A vertical orifice is 10 cm. square and has an actual flow of 28 Ips with Cv=0.95, Cv = 0.62 as shown in the figure. If the liquid is oil (s.g. = 0.85), what is the head, h in meter over the orifice is required? determine the theoretical velocity of the jet determine the theoretical flow (Ips).
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discahrge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes?
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
For the system below, let the pump exhaust gasoline at 65 gallons per minute to the atmosphere through a 3-cm-dimater opening. When x = 3 m, y = 2.5 m and z = 2 m, the pipe friction head loss along the entire length of the pipe has been shown to be hf = 3.7 V 2 /(2g) empirically, where V is the velocity in the pipe. Estimate the horsepower to be delivered by the pump.
A projectile-like object with maximum diameter of 20 cm is placed at the exit of a 25-cm-diameterpipe. Water flows through the pipe. At the upstream location 1, the velocity is uniform and equalto 2 m/s. The water exits to the atmosphere where the pressure is 100 kPa. Find the force requiredto hold the object in place. Be sure to state your assumptions.