A vessel 1 m square in cross section has two identical orifices provided in one of its sides at depth of 2 m and 3 m respectively below the free surface of water in the tank. Assume Cy = 0.98 and C. = 0.65. The diameter of orifice is 50 mm. The tank has a constant acceleration of 4.905 in the direction of the jet. Determine: %3! %3D

A vessel 1 m square in cross section has two identical orifices provided in one of its sides at depth of 2 m and 3 m respectively below the free surface of water in the tank. Assume Cy = 0.98 and C. = 0.65. The diameter of orifice is 50 mm. The tank has a constant acceleration of 4.905 in the direction of the jet. Determine: %3! %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

diameter of cylindrical tank = 2 meters depth of cylindrical tank = 8 meters diameter of sharp-edge orifice = 100 mm The standard orifice is placed at the side 1 meter above the bottom. When at rest, the depth of water is 5 meters Considering that the volume of water is constant, what is the rate of discharges from the standard orifice: a. When the cylindrical tank has a constant velocity of 3 m/sec in the opposite direction of the jet. b. When the cylindrical tank has a constant acceleration of 6 m/sec^2 in the opposite direction of the jet. Consider the figures below*
A sharp-edged orifice 100 mm in diameter, in the side of tank having a horizontal cross-section 2 m square, discharge waterunder a constant head. The rate of inflow over which the head was kept constant is suddenly changed from 20 l/s to 30 l/s.How long will it take, after this change occurs, for the head to become 2 meters? The coefficient of discharge may be consideredconstant and equal to 0.60
A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. a. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled. b. Determine the largest pressure developed in the tank.
1. An orifice in the side of a vertical tank discharges oil (sp. gr. = 0.82) under a head of 4.0 m. and 25 KPa pressure acting on the surface of the oil. If the diameter of the orifice is 5 cm, the coefficient of contraction is 0.62, and the head lost on the orifice is 45 cm, determine the discharge, coefficient of velocity, and the coefficient of discharge.
The head-discharge relationship for a certain pump can be represented by the equation H = 28 - 9Q2. The pump is fixed 2.5 m above the water surface in a river and it forces the water to a tank at a level 10 m above the pump. The suction and delivery pipes are 15 m and 740 m long, respectively and each pipe is 0.5 m in diameter. The pipe coefficient of friction (f)is 0.017. Estimate the discharge (in m3/s) at the best operating point for the pumping system. Q = 0.9 m3/s Q = 1.1 m3/s Q = 0.4 m3/s Q = 0.6 m3/s
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The suction pipe is 350mm in diameter and 12m in length, and the delivery pipe is 550mm in diameter and 40m in length. The friction factor of the pipe system is f=0.005. Q. Calculate the maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa
A right circular tank 6 m. in diameter and 12 m. high is filled with 6 m. of oil sp.gr. = 0.80 and 6 m. of water. A horizontal circular orifice 75 mm in diameter is situated at the bottom. Coefficient of velocity is 0.98 and coefficient of contraction is 0.61. Neglecting velocity of approach. a. Determine the velocity of the jet issuing from the orifice at the instant the surface of the liquid in the tank is 6.5 m. above the orifice. b. Determine the discharge in kg/sec. through the orifice at the instant the surface of the liquid is 5.5 m. above the orifice. c. Compute the total time to empty the container.
A right circular tank 6 m. in diameter and 12 m. high is filled with 6 m. of oil sp. gr. = 0.80 and 6 m. of water. A horizontal circular orifice 75 mm in diameter is situated at the bottom. Coefficient of velocity is 0.98 and coefficient of contraction is 0.61. Neglecting velocity of approach.a. Determine the velocity of the jet issuing from the orifice at the instant the surface of the liquid in the tank is 6.5 m. above the orifice.b. Determine the discharge in kg/sec. through the orifice at the instant the surface of the liquid is 5.5 m. above the orifice.c. Compute the total time to empty the container.
A cylindrical tank 1 m diameter and 3 meter high contains 1m of water, 1.2 m of oil (SG=0.8) and air under a pressure of 15 kPa. Find the discharge through a 5 cm diameter orifice 30 cm above the bottom of the tank, if c=0.61
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The suction pipe is 350mm in diameter and 12m in length, and the delivery pipe is 550mm in diameter and 40m in length. The friction factor of the pipe system is f=0.005. Q1. Calculate the maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa Q2. Calculate the energy to be supplied by the pump per unit mass of water transferred Q3. Calculate the input power required by the pump, which is 60 % efficient
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The suction pipe is 350mm in diameter and 12m in length, and the delivery pipe is 550mm in diameter and 40m in length. The friction factor of the pipe system is f=0.005. Q1. Calculate the maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (m) Q2. Calculate the energy to be supplied by the pump per unit mass of water transferred (J/Kg) Q3. Calculate the input power required by the pump, which is 60 % efficient (kW)
A D0 = 12-m-diameter tank is initially filled with water 2 m above the center of a D = 10-cm-diameter valve near the bottom. The tank surface is open to the atmosphere, and the tank drains through a L = 95-m-long pipe connected to the valve. The friction factor of the pipe is given to be f = 0.015, and the discharge velocity is expressed as V =√ 2gz/(1.5 + fL/D) where z is the water height above the center of the valve. Determine (a) the initial discharge velocity from the tank and (b) the time required to empty the tank. The tank can be considered to be empty when the water level drops to the center of the valve.