An open cylindrical tank having a radius of 0.30 m. and a height of 1.20 m. is filled with water at depth of 0.90 m. How fast will it be rotated about its vertical axis so as to produce zero pressure with 0.20m from the center of the tank? Unit of the Correct Answer: rpm

An open cylindrical tank having a radius of 0.30 m. and a height of 1.20 m. is filled with water at depth of 0.90 m. How fast will it be rotated about its vertical axis so as to produce zero pressure with 0.20m from the center of the tank? Unit of the Correct Answer: rpm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A vertical cylindrical tank is 9 m high and 5 m in diameter. It is two thirds full of water and is…

A: Solution 1) Solution Given Data Cylindrical tank height= 9 m Diameter= 5 m Rotational speed= 48 rpm

Q: Water from a reservoir is raised in a vertical tube of internal diameter D = 45 cm under the…

A: the atmospheric pressure, Patm=96KPa.The diameter of tube, D =45cm =0.45m

Q: 80 kPa el. 12 m e 120 kPa el. 7m A pressure gauge at elevation 12m at the side of a tank containing…

A: we can use Bernoulli equation Here Given Data P1=80 kpa P2=120 Kpa Z1=12 m Z2=7 m Applying…

Q: 1. Oil is placed inside a closed container, but it is not filled to the top. The vacant area above…

Q: A liquid with a density of 900 kg/m³ flows straight down in a 6-cm-diameter cast iron pipe. Estimate…

A: Density of liquid, ρ=900 kg/m3 Diameter of pipe, D=6 cm=0.06 m Length of pipe, L=20 m Average…

Q: 1. Consider a spherical elevated water tank with a diameter of 30 feet. The top of the tank is 90…

Q: 4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the…

Q: Homework 14 A cylindrical vessel closed at the top and bottom is 300mm inn diameter, 1m long and…

A: given data diameter of the vessel=300 mm=0.3mlength=1 mdepth of water=0.8 mspeed of rotation is…

Q: A large tank open to the atmosphere is filled with water to a height of 5 m from the outlet tap. A…

A: Given that, A tank filled with water, H = 5m

Q: A vertical cylindrical tank has an orifice for its outlet. When the water surface in the tank is 5 m…

A: given: case 1 initial height of water, z1= 5m surface pressure= 1 atm = 1.01x105 KN/m2 time taken=…

Q: (2) The tank below is cylindrical with a diameter of 10 m . The outlet is a cylindrical frictionless…

Q: A right circular cylindrical tank container, 2 meters in diameter and 4 meters high, is ½ full of…

Q: - Closed top Open to atmosphere 1 m Plan view (view E-E) Open to atmosphere 2 m 1 m 1 m 1m Air Air 2…

Q: ) A nozzle, which reduces from 45mm to 30mm in diameter, discharges water at a rate of 30 L/s. If…

Q: Determine the upward thrust F on .5 the semi-cylindrical top of the container shown below. The…

Q: A vessel containing liquid, S = 1.5, is rotated about a vertical axis. The pressure at one point…

Q: Water flows from a reservoir into a closed tank in which the pressure is 70 kN/m2 below atmospheric.…

A: Given data, P1 = 0 Pa (Reservoir) P2 = 0-70000 Pa (Tank) z1 = 6 m V1 = 0 (Reservoir)

Q: A fire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X= 0)…

A: a) Using Bernoulli’s equation, Here, the pressure is atmospheric so the pressure p1 and p2 are…

Q: In the figure shows a container having a width of 1.50 m. Calculate the total forces on the ends and…

A: Pressure and force are related, and so you can calculate one if you know the other by using the…

Q: A cylindrical tank contains a certain liquid (SG = 2.75) to a depth of 0.4 m. A pressure of 78 kPa…

A: Given- SG=2.75d=0.4mP=78Kpaaupward=-3.43m/s2P=?

Q: A cylindrical vessel 15 cm diameter and 40 cm long is completely filled with water. The vessel is…

Q: A pressurized tank of water has a 12-cm-diameter orifice at the bottom, where water discharges to…

A: P1=40psia Patm=14.5psia Z1=3m Z2=0m

Q: A body moving through still water at 6 m/sec produces a water velocity of 4 m/sec at a point 1 m…

Q: A tank is containing water up to a height of 2 m. Calculate the pressure at the bottom of the tank…

A: given data : depth (h)=2 m

Q: If the velocity at point A is 18m/s, calculate the (a) velocity of the jet at C in m/s, (b) velocity…

A: Given Velocity at A = 18m/s Assume B as datum = Z3 = 0

Q: The absolute pressure in a closed gas tank is 260 KPa. Compute the pressure head in meters of water.…

Q: A cylindrical tank of 3 m height and 5 cm^2 cross-sectional area is filled with water up to a height…

A: Gauge pressure is the relative pressure to atmospheric pressure when the gauge pressure is above…

Q: (50%): A large tank open to the atmosphere is filled with water to the height of 5m from the outlet…

Q: An open jet of water at 20 ℃ exits a nozzle into sea-level air and strikes a stagnation tube, as…

A: Continuity equation is given by- a1v1=a2v2v1=16144v2v1=v29 Bernoulli equation is given by-…

Q: a pipe has a pressure of 4000 pascal and is connected to a 36 degree inclined single column…

A: We will take pressure at top level of mercury in reservoir same from both left and right side.

Q: A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other…

Q: An open cylindrical tank 1.0m in diameter and 10 high contains water up to a height of 8m. If the…

Q: A cylindrical drum of 1500 m diameter contains 1000 litres of water and is open at the top. Find the…

A: Introduction: When a cylindrical vessel containing liquid rotates with its axis vertical, then the…

Q: Compute the depth of the center of pressure for a vertical circular gate having a diameter "h" when…

A: Using centre of pressure formula

Q: ire hose has 100 mm diameter which reduces to a 20 mm nozzle discharging at 10+X m/s. (X=…

A: a) Given, Velocity = 16 m/s, Let the water reach to the height 'h' m, then Applying Bernoulli…

Q: An open rectangular tank, 9.62 ft. high, 11.29 ft. long, and 5.19 ft. wide, has liquid (SG = 0.53)…

A: Consider the following figure.

Q: A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other…

Q: Three liquids given the following properties are poured into the cylindrical container with a…

A: To Find Pressure at 0.5 m above the tank bottom.

Q: 1.0m 0.20m O(pivot) W= 35 KN 6o cm diam 5 Cm iam h= 7m oil (2) (s = 0.85)

A: diameter of the plungerd=7.5 cmarea of the plungera=π47.52a=44.17 cm2diameter of the ramD=40 cmarea…

Q: 4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the…

Q: A cylinder glass tubing 2.8 cm. inside diameter and 90 cm long with one end closed is immersed…

Q: A cylindrical tank 0.8m high and a diameter of 0.3m is partially filled with water to a certain…

Q: A jet from the nozzle, 30mm in diameter, is directed against a stationary flat plate. The velocity…

Q: Q1: the pressure at point A is 172 pa. All fluids are at 20°C. The air pressure in the closed…

A: to find pressure at point B

Q: An open rectangular tank 3.8m high, 2.5m wide and 6m long is filled with water at a depth of 2.2m.…

Q: A closed cylindrical tank with 0.60 m diameter and 1.0 m height is fully-filled with water. The tank…

A: To find the pressure -

Q: A jet from the nozzle, 30mm in diameter, is directed against a stationary flat plate. The velocity…

A: Given data: VJet = 20m/s, Vplate = 5m/s, Diameter of jet = 30mm It is asked to find pressure on…

Q: 0.20 m h 0.20 air m y 0.60 m 0.60 (0.60) = 0.40 I 0.30 m 0.30 m 0.30 0.30

Q: In a pump that works with cold water, the discharge pressure gauge located 7.5 m above the axis of…

A: Head of the pump: The maximum height that a pump achieves the pumping against the gravity is known…

Q: The tank contains a liquid having a density of 1.22 slug/ ft. Determine the weight of the liquid…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

An open cylindrical tank having a
radius of 0.30 m. and a height of 1.20
m. is filled with water at depth of
0.90 m. How fast will it be rotated
about its vertical axis so as to
produce zero pressure with 0.20m
from the center of the tank?
Unit of the Correct Answer: rpm
128.107
201.278
207.218
O 218.207

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

At what speed should the tank in Problem 5.23 be rotated in order for the center of the bottom of the tank to have zero depth of water? Ans.9.83 rad/sec
A rectangular reinforced concrete beam with width of 300 mm & effective depth of 600 mm is subjected to a service bending moment of 200 kN.m. The beam is reinforced with 4-32 mm diameter bars. n = 8. 1. Compute the distance kd? a. 246.33 mm b. 353.67 mm c. 170.33 mm d. 302.33 mm 2. Which of the following gives the moment of inertia about N. A.? a. 4173.81 x 106 mm⁴ b. 3471.81 x 106 mm⁴ c. 4371.81 x 106 mm⁴ d. 4713.81 x 106 mm⁴ 3. Which of the following most nearly gives the maximum stress in steel in Mpa? a. 100 b. 110 c. 120 d. 130
l=160mm, b=60mm. AB rotating with constant angular velocity 1600 rpm clockwise. determine the velocity of P. θ = 45°
If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16ft and water depth of 4.5ft. The channel bottom drops 0.1ft every 100ft. Length, n=0.015 Compute the velocity in ft/s (using Kutter's) a. 6.513 b. 1.653 c. 3.516 d. 5.316
To prevent the ladder weighing 600N from sliding down, the man exerts a horizontal force at C. The coefficient of friction at A= 0.2 while surface B is frictionless Find the vertical reaction at Aa. 600N c. 500Nb. 700N d. 800NFind the horizon reaction at Aa. 150N c. 210Nb. 180N d. 120NFind the horizon force exerted by the man at Ca. 533.3N c. 333.3Nb. 667.7N d. 767.6N
Find the magnitude and direction of the friction force when theta=35deg and P=200N
solving equations 5 and 6 actually gives you EIθB=60.69, EIθC=-210.52
Determine the horizontal force Q applied to block B that would cause the system to impend its motion to the left. (All contact surfaces have the same angle of friction of 11.31 degrees except the horizontal surface beneath block B with 16.7°)
V=38 h1=96 h2=12 D1=6 D2=3 angle = 20 degree
An 80 m spiral is used to connect a 4o simple at both ends. 1. Compute the long tangent. a. 53.37 m b. 42.51 m c. 26.73 m d. 36.41 m 2. Compute the deflection angle at second quarter. a. 2 deg b. 0.67 deg c. 1.33 deg d. 0.33 deg 3. Compute the tangent distance if I = 50deg. a. 261.51 m b. 185.62 m c. 128.14 m d. 174.02 m
the catapult is used to launch a ball such that it strikes the wall of the building at the max. height of its trajectory. if it takes 1.789 secs to travel from A to B, determine the angle of release in degrees. use y=3.84ft. and x=16.68ft.