A W 18 x 40 are spaced at 2.4 m on center. The beams are simply supported on a span length of 9 m. and support a 150 mm thick reinforced concrete slab. Assume A36 steel and full lateral support of the compression flange. Unit weight of the concrete is 24 kN/m³. 2.4 2.4 h-393.7 mm Properties of W 18 x 40 (wt. beam - 60 kg/m) A = 7613 mm? d- 454.66 mm tf = 13.34 mm bf = 152.78 m tw = 8 mm Sx = 1121 x 10° mm³ Zx = 1285 x 10° mm³ Fy = 248 MPa Determine the ultimate shear strength of the section (kN)

A W 18 x 40 are spaced at 2.4 m on center. The beams are simply supported on a span length of 9 m. and support a 150 mm thick reinforced concrete slab. Assume A36 steel and full lateral support of the compression flange. Unit weight of the concrete is 24 kN/m³. 2.4 2.4 h-393.7 mm Properties of W 18 x 40 (wt. beam - 60 kg/m) A = 7613 mm? d- 454.66 mm tf = 13.34 mm bf = 152.78 m tw = 8 mm Sx = 1121 x 10° mm³ Zx = 1285 x 10° mm³ Fy = 248 MPa Determine the ultimate shear strength of the section (kN)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A column is made of steel and concrete, if the normal forces on steel and concrete are 6.8kip and 145kip and the allowable stresses of steel and concrete are 36ksi and 5.5ksi, and the cross sectional areas of steel and concrete are 0.3068in^2 and 45.5456in^2, determine whether the still or concrete will fail when given a yield factor of safete of 1.69
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
Determine shear force in every portion of beam. The load 80 kn is 6 m from support d
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Use cantilver method Calculate for the axial force in kN at member CB a = 40.4 kN, b = 21.7 kN, c = 3.6 m
Determine the force in member GB, CE, ED. Use Y=40X=205A=1
Calculate for the axial force in kN at member CB using cantilever method a = 40.4 kN, b = 21.7 kN, c = 3.6 m
reply plss An overhang beam carries a concentrated load, P and a uniform load, w = 15 kN/m. If the point of contra-flexure (where bending moment is zero) is located 0.5 m from support B, determine the absolute value of P (in kN).
A masonry terrace of 65mm thick concrete surface with 35mm thick cement tiles rest on 100mmx 200mmtimber spaced at 250mm on centers acting as simple beam with effective span of 3.8 meters. Weight of woodis7.5Kn/M^3 and masonry to be 18KN/m^3. Ew = 13.8GPa. b. Determine the uniform load it could support with respect to shear.
A rigid beam ABC is supported at C by a pin support, and at A and B by timber struts AD and BE which are in turn supported by pin supports at D and E respectively (Figure 1). The struts AD and BE are constructed using F11 timber (refer Figure 2) with square cross section 40 mm x 40 mm. A uniformly distributed load of 10 kN/m acting horizontally to the right is applied along the complete length ABC. Under the action of this load, in addition to any changes in the lengths of the struts, the pin support at C settles by 1 mm to the right. Assume that the beam and struts are weightless and that the struts will not buckle. (a) Using equilibrium and compatibility considerations determine the support reactions at C, D and E. Hint: Since the struts AD and BE can transfer only axial force, the reactions at D and E act horizontally (that is, there are no vertical reaction components at D and E). (b) Find the normal stress, normal strain and change in length of strut AD.
Beam ABCD has a length of 14 meters, where points A nd D are located at theleftmost and rightmost end, while point C is located 10 meters from point A andpoint B is located midway between A and C. The beam is supported at A (hinged)and at C (roller). A concentrated load P is loaded at B and a uniform load "w" isapplied in the span(segment) CD. If P = 60 kN and w = 5 kN/m, compute the slopeat D in degrees
A 100 mm x 200 mm beam 6 m long is supported by a roller at its ends and at midspan. It carries a uniform load of 7.5 kN/m excluding its own weight, if the Weight of the wood is 5.6 kN/m² and the support at midspan is 26.5 kN, Determine the shear and moment diagram of the beam.