A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7.8 m long, fixed at the top and bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the effective slenderness ratio with respect to strong axis buckling using theoretical value of k.

A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7.8 m long, fixed at the top and bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the effective slenderness ratio with respect to strong axis buckling using theoretical value of k.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.9.4P

See similar textbooks

Similar questions

Read the question carefully and give me right solution according to the question. A W12x79 of A573 Grade 60 (Fy=415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at the bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the effective slenderness ratio with respect to strong axis buckling using theoretical value of k.
Compute for the force in members FH, GH, and GI (USE METHOD OF SECTIONS) *For load P, take the last digit of your ID number example: ID # : 2187525, then P= 5 kN IF ZERO IS THE LAST DIGIT, TAKE THE 2ND TO THE LAST DIGIT example: ID #: 2187520, then P= 2 kN
Situation 17. A w12x79 of A573 Grade 60 (Fy-415MPa) steel is used as a compression member. It is 8m long pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows Ag=14,500 sq.mm = 258.6x10^6 mm^4 Iy=84.375x10^6 mm^4 Calculate the critical slenderness ratio with buckling about strong axis. calculate the critical slenderness ration with buckling about weak axis. calculate the flexural buckling stress Fcr in MPA
A reinforced concrete beam, b by h with tensile reinforcement of 6-25mm diameter bars is simply supported on a clear span of 12m. Given: fc = 12 MPa fs = 140 Mpa wc = 24 kN/m3 n = 12 b = 331 mm h = 602 mm d = 582 mm determine the ff. 1. What is the distance from the top fiber of the beam to the neutral axis in mm? 2. What is the gross moment of inertia of the section in mm4? 3. Compute the moment capacity of concrete in kN-m. 4. Compute the moment capacity of steel in kN-m. 5. Aside from the uniformly distributed self-weight of the reinforced concrete, what will be the maximum two equal concentrated loads it can carry that will be located at its third points in kN? pls solve completely
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
The dimensions of a rectangular beam are limited to b = 300 mm and h = 770 mm. Assume that the bar centroid of tension bars is 70 mm from the beam edge and that of compression bars is 60 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the following for a factored bending moment of 1200 kN: a. Maximum steel ratio limiting the tensile strain to 0.004. b. Required amount of tensile reinforcement if the tensile steel strain is limited to 0.005. c. Required amount of compression reinforcement.
3. A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: a. Effective flange width of an interior beam in mm =____? ____ b. Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ____?____ c. Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =____?_____
Determine the shear strength for a built-up I shape made up of A709 Gr HPS 70W steel. Flanges: PL 18”x 1.5” Web: PL 36”x 5/8” Unstiffened
The wooden section of the beam below is reinforced with two steel plates as shown. determine the moment maximum internal M that the beam can withstand if the allowable stresses for wood and steel are (σadm)wood = 6 MPa and ((σadm)steel = 150 MPa, respectively. Use E(wood) = 10 GPa and E(stell) = 200 GPa.
A beam of T-section is supported and loaded as shown in the figure below. The cross section has width b = 2.5in., height h = 3in., thickness t = 0.5in, c1 = 2in, and c2 = 1in. Determine the maximum tensile and compressive stresses in the beam if I = 2.0833 in^4 .
13.A rectangular beam has b = 300 mm and d = 410 mm. The beam is used to carry a factored moment of 20 kN-m. Assume f'c = 28 MPa and fy = 280 MPa. Calculate the required steel area in mm2. Express your answer in nearest whole number
The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained under a sustained ultimate bending moment of 1,200 kN.m. Compression bars centroid is 70 mm from beam edge. 6,180 3,839 4,387 5.353