A wet sand sample has a volume of 4.64 x 10-4 m3 and weighs 8N. After oven-drying, the weight reduces to 7.5N. Don't assume the value of Gs.Calculate the following: a. Void ratio b. Degree of saturation.

A wet sand sample has a volume of 4.64 x 10-4 m3 and weighs 8N. After oven-drying, the weight reduces to 7.5N. Don't assume the value of Gs.Calculate the following: a. Void ratio b. Degree of saturation.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Related questions

Q: Find the height of the free surface if 0.8 cu.ft. of water is poured into a conical tank as shown in...

A: The values and diagram given in the question are as follows: Height of cone(h)=20 in base radius of ...

Q: Problem 8. Solve all reactions (Ax, Ay, Cx, and Cy) for this structure. Note: force is transferred o...

Q: 2. Dozer Production Calculation How long will it take for a track-type dozer w/straight blade to mov...

A: A dozer is a motorized machine equipped with a metal blade in front used to push and move materials....

Q: The design process is a project management guide used to oversee the execution of a large project, t...

Q: Completely determine the resultant with respect to point O of the force system shown in figure. 1414...

Q: Determine the scalar components of F1, F2 and F3. F2 = 500 N F1 = 600 N 3 35°

Q: A 25 ml sample of treated waste water requires 175 ml of distilled water to reduce the odour to a le...

Q: PROBLEM 2 (15 points): The magnitude of stresses of the soil element represented by the figure below...

Q: 1. The observed interior angles of a triangle and their corresponding number of times measured are a...

Q: A two-lane major road with 40 mph east west direction crosses a two-lane minor road with 30 mph at a...

Q: A prismatic bar 50°F is imbedded in a rigid concrete wall. The bar is 40 in long nd has a cross-sect...

Q: Three common soil sampling tools along with their sizes are given below. Choose the incorrect statem...

A: Area ratio=D22-D12D12×100%where,D1=inside diameterD2=outside diameterArea ratio should be as small a...

Q: Handle grip Socket Cutting edge Shaft Blade

A: A shovel is a tool used for digging, lifting and moving materials such as soil, sand, gravel etc. Th...

Q: 2. Compute for the reaction at the center so that there will be no deflection at the center of the s...

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. 2 ft C 4 ft 4 ft B...

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

Q: Problem 4-145 4-145. Replace the loading by an equivalent resultant force and couple moment acting a...

A: Given, A structure, FBd:-

Q: A plane truss has a downward applied load P at joint 2 and another load P applied leftward at joint ...

A: To find force in member 5-6

Q: Consider the following data: • Average number of vehicles (overtaking - overtaken) = 1 · Average num...

A: Given data,

Q: A block of wood floats in water with 20 cm projecting above the water surface. The same block when p...

Q: A concrete cube weighs 441 lbs. If the specific gravity of the concrete is 2.40, what is the length ...

Q: Trejectory ot a fluid part X = a.(1+).b. t)² y= 6 Equations are given 1+A.b.E A and u are two consta...

A: Given equations are x = a1+λ.b.t2 y= b1+λ.b.t Let velocity in x- direction Vx = dxdt Let velocity i...

Q: 15 KN/n A to 40KN ith Calculate bending moment and shear by using the moment distribution method of ...

A: .

Q: 1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle sec...

Q: Find the reaction at points A and B below: 50k / ft 40 kip 50 kips- ft A B - 4.5 ft- 5ft- 8 ft-

A: We have to determine the value of reaction of the point A and B below as per the given data.

Q: Given the bended rod as shown below. Determine the following: a.) The x-component of Reaction A. b.)...

A: The unknowns are three in number. Using equations of equilibrium summing up moments at A the value o...

Q: A simple curve of the proposed highway extension have a direction of tangents AB due North and BC wi...

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length ...

A: For the given metal bar,

Q: A steel rod, circular in cross-section, tapers from 30 mm diameter to 15 mm diameter over a length o...

A: Given:- The steel rod tapers from 30 mm diameter to 15 mm diameter The length of the rod = 600 mm Th...

Q: The cantilever beam is supported by a fixed support at A, and subjected to the force F = couple M = ...

Q: The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average normal st...

Q: The 30-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure ...

Q: Determine the plastic section modulus Z, and Z, of the T-section shown below. Determine also the pla...

A: ##Calculation of Plastic Section Modulus and plastic Moment Capacities about x and y axis

Q: Please answer it asap completely and neatly for an upvote. Thank you. An eccentrically loaded founda...

A: step 1-

Q: A simple curve of the proposed highway extension have a direction of tangents AB due North and BC wi...

Q: A footballer kicks a ball on horizontal ground giving it an initial velocity of 35 m/s at an angle o...

Q: ROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position s the...

A: x=1m T=15.5kN

Q: For the retaining wall given below, what will be the active thrust acting per unit width of the wall...

Q: For the system shown. a. Determine the acceleration of the two bodies. b. Determine the tension on e...

A: As per company guidelines , we are allowed to answer first 3 sub parts of the question . For solutio...

Q: DISCUSS ION QUESTIONS 1. What are the advantages of using a decentralized organization structure at ...

Q: A slope of infinite extent with a slope angle of 22° is made of a soil having c = 0 and angle of int...

Q: The results shown in the following table were obtained at the pea a series of CD TXC with a constant...

A: Step 1: σ3 = 70, 140 σ1 = σ3 + σd= 265+70, 494+140 = 335, 634 Horizontal axis is labeled normal stre...

Q: What are the differences between coarse aggregates coming from processing plants and coarse aggregat...

A: Coarse aggregate are the irregular shaped broken stones or rounded natural gravel used to make concr...

Q: A 30 m steel tape is used to measure a rectangle at 22°C with a pull of 42 N. The sides are recorded...

A: Total correction for the length = True length - Recorded length True length of rectangular = Length ...

Q: Give an example for type of load classification according to Method of Application 1 centric load ...

Q: 1-Determine final consolidation settlement 2-if the sett lement after 6months of aload applidcation ...

Q: The shaft, lever, and handle are welded together and constitute a single rigid body. Their combined ...

Q: 625 mm 10 |20 kN/m 500 mm 6 m 100 mm

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

Q: 2. By the Volume and Area Method, find the quantity of ce- ment, sand and gravel of the concrete pav...

Concept explainers

Laboratory Determination of Hydraulic Conductivity

Hydraulic conductivity is the measure of flowability of water inside the soil in the presence of a hydraulic gradient. The hydraulic gradient is defined as the difference in the water heads in the soil, which induces a water motion. In simple terms, a hydraulic gradient is the presence of a potential that induces a flow of water.

Question

100%

A wet sand sample has a volume of 4.64 x 10^-4 m³ and weighs 8N. After oven-drying, the weight reduces to 7.5N. Don't assume the value of Gs.Calculate the following:

a. Void ratio

b. Degree of saturation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Laboratory determination of hydraulic conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

a wet sand sample has a volume of 4.6 x 10^-4 m^3 and weighs 8.1 N. After oven-drying, the weight reduces to 7.5 N. Use Gs=2.59. Calculate the degree of saturation in decimal form
A wet sand sample has a volume of 4.64 x 10-4 m3 and weighs 8 N. After oven-drying, the weight reduces to 7.5 N. Calculate the water content, void ratio, and degree of saturation.
The results of a constant-head permeability test for a fine sand sample having a diameter of 150 mm and a length of 300 mm are as follows: constant head difference = 500 mm, water collected in 5 min = 350 cm3, void ratio of sand = 0.61. Determine the hydraulic conductivity.
The results of a constant-head permeability test for a fine sand sample having a diameter of 150 mm and a length of 300 mm are as follows • Constant-head difference = 500 mm • Water collected in 5 min = 350 cm3 • Void ratio of sand = 0.61 Determine: a. Hydraulic conductivity, k (cm/sec) b. Seepage velocity
The results of a constant-head permeability test for a fine sand sample having a diameter of 70 mm and a length of 140 mm are as follows (refer to Figure 7.5):• Constant-head difference = 550 mm• Water collected in 7 min = 450 cm3• Void ratio of sand = 0.8Determine:a. Hydraulic conductivity, k (cm/sec)b. Seepage velocity
2. Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen = 16 cm Diameter of specimen = 96 mm Constant Head Difference = 50 cm Volume of water collected in 4 min = 420 cc Void ratio of the soil specimen = 0.55 a. Determine the hydraulic conductivity of the soil in m/min. Round off to four decimal places. b. Determine the discharge velocity in m/min. Round off to four decimal places. c. Determine the seepage velocity in m/min. Round off to four decimal places.
The max and min dry unit weights of sand were determined in the laboratory to be 18.31KN/M3 and 15.25KN/M3 respectively.Determine the dry unit weight in the field if the relative density is 0.64.
For a constant-head permeability test in a sand, the following are given: (L = 300 mm, Water collected in 3 min = 620 cm^3, A = 175 cm^2, Void ratio of sand = 0.58, h = 500 mm). Determine the seepage velocity.
For a constant head permeability test in a sand, the following values are given:• L 350 mm• A 125 cm2• h 420 mm• Water collected in 3 min 580 cm3• Void ratio of sand 0.61Determine:a. Hydraulic conductivity, k (cm/sec)b. Seepage velocity
The volume of clay sample having a natural water content of 40% is 0.0009 ft3 and its wet weight is 0.096lb. Calculate the degree of saturation of the sample, if G = 2.75.
The results of a constant head permeability test for a fine sand are as follows: Diameter of the sample = 41 cm Length of sample = 66 cm Constant head difference = 30 cm Time of collection = 473 secs Weight of water collected = 416 grams Find the seepage velocity in cm/min. if the void ratio is 0.43.
Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen = 16 cm Diameter of specimen = 96 mm Constant Head Difference = 50 cm Volume of water collected in 4 min = 420 cc Void ratio of the soil specimen = 0.55 a. Determine the seepage velocity in m/min. Round off to four decimal places. b. determine the discharge velocity in m/min. Round off to four decimal places.