A) What are the considerations should be taken at the design of the Thyristor gate trigger signal? B) List the techniques that used to commutates Thyristor?

Q: 1-Design an ON-OFF transistor switch to control a 12 volt DC motor rotation.

A: As per the rules we can answer only one question, please post the remaining questions as the…

Q: What is the function, operation, and application of switching regulator?

A: Due to advancement in power electronics, in today's scenario most of the electrical appliances uses…

Q: Q1//Determine the DC bias voltage VCE and the current IC for the configuration of figure (3) using…

A:

Q: How avoid race condition in writing the verification code of a given design specification.

A: To verify a design we write test bench to check that it meet specification. Verification can be done…

Q: Single phase full Bridge Design a basic DC / AC converter (Inverter) power circuit, describe the…

A:

Q: What is the difference between dc-dc switching mode regulators and PWM Inverters ?

A: Switching regulators is one of the efficient way to convert one DC/DC voltage to the other.and also…

Q: Q2/ What is the advantage of Digital signal processing DSP, and where should be used?

A:

Q: Discuss the operation of an AM demodulator circuit with emphasis on the effects of the components to…

A: A mixer or product detector is used with a local oscillator signal in the synchronous AM…

Q: 1. Explain briefly another way for implementing Multivabrator Circuit other than by using transistor…

A: ''Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is meant by sensor bias voltage?

A: Bias voltage is defined as the amount of voltage  that an electronic device needs in order to power…

Q: Discuss the effect of adding a smoothing capacitor to the output of the rectifier on the DC value of…

A: We known that capacitor opposes rate of change in voltage .

Q: (a) Draw the circuit diagram of 2-bits flash (simultaneous) method analog to digital converter and…

A: We are authorized to answer one question at a time. Since you have not mentioned which question you…

Q: Explain driven LCR circuit?

A: Explain driven LCR circuit?

Q: 3. What is the purpose of an Enable Input on a Multiplexer? 4. How does the 74151 Multiplexer treat…

A:

Q: digital electronics 2 In which option is the logic circuit equivalent of the RTL circuit given in…

A: Given :    Here they have mentioned the the sister transistor logic circuit.     From the given…

Q: What is the effect of the gate current in the operation of the TRIAC?

A: The TRIAC is defined as the triode for the alternating current. The triac is just like the set of…

Q: What are the purpose of the DC biasing circuit

A: Transistor Biasing is the process of setting a transistors DC operating voltage or current…

Q: Define FACTS and write its necessity and benefits. With neat diagrams, briefly describe different…

A:

Q: Using a circuit diagram and output waveform, describe the mechanism of a square wave oscillator.

A:

Q: Q) Design 8:1 multiplexer using 4:1 multiplexer and give an example and ?explain why

A: The block diagram of 4x1 MUX is The block diagram of 8x1 MUX is

Q: Explain the operation of the circuit by drawing the AC power control (regulation) circuit with the…

A: AC power control circuit:

Q: . What is the purpose of conducting Open Circuit (OC) test?

A:

Q: What is AVR?

A: AVR is tends for Automatic Voltage Regulator. AVR is an electronic device which is used to maintain…

Q: Which of the following is an example of a PLC output section?

A: PLC refers to the programmable logic output which has a several input and several output

Q: What is the operation of a Zener voltage regulator? How it works?

A:

Q: What distinguishes field programmable gate arrays from other types of semiconductors?

A: According to the question, we need to distinguish field-programmable gate arrays from other types of…

Q: What is analogue signal?

A: The analogue signal is continuous in nature and it represents both time and amplitude.

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: .1. The figure represents the Buck Regulator that provides a smoothed Dc current to a practical…

A:

Q: c) When considering thyristor switching why is Isolated Gate Control needed ?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: а. What is an accumulator system, explain with mathematical expression. b. Find whether an…

A: Bartleby has policy to solve only first 3 subparts of a question. For solution of rest questions…

Q: 1- Define voltage regulator ? what is its main job? 2- How can we specify the quality of voltage…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Please describe as simply as possible in detail, what a multiplexer circuit is, how it works. Please…

A:

Q: What is the stablisation in transistor biasing?

A: Transistor biasing: It represents DC conditions. The maintenance of proper voltage of collector…

Q: Which IC technology has the lowest power dissipation in general?

A:

Q: Describe the basic types of input test signals.

A:

Q: Explain How is the inverter type ACU open-loop systems calibrated

A: An open-loop system is a sort of control system in which the system's output is determined by the…

Q: Explain the role of LVDT and Weight transducer

A: LVDT is a displacement transducer .it consists of one primary and two secondary coils. A magnetic…

Q: What is the operation of a Transistor voltage regulator? How it works?

A:

Q: b) Which type of VFD architecture does require a braking resistor; Voltage Source Controller or…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Which is the output function F for the digital circuit shown in the figure is correct

A: AND and OR gate combination For two input AND gate output y=AB For OR gate y= A+B

Q: Describe the operation of binary ripple counters

A:

Q: What is the problem of using a pushbutton or a switch as a digital input to a microcontroller. Then,…

A: We need to identify the problem of using a pushbutton or a switch as a digital input to a…

Q: Sketch the transistor input and output characteristics of CE configuration and briefly   explain the…

A:

Q: Write about computer simulation of ASSESSING THE TRANSIENT STABILITY.

A: Transient Stability- It is defined as the ability of the power system to return to its normal…