a) What is the relation between stress at the tension side and diameter of the fatigue test specimen? b) What is the unit of the endurance limit? c) How can the endurance limit for a fatigue analysis be calculated when real material properties are not available? d) Why some of the materials perform endurance limit, and some don't? Give some examples from each group of material and discuss the reason.

a) What is the relation between stress at the tension side and diameter of the fatigue test specimen? b) What is the unit of the endurance limit? c) How can the endurance limit for a fatigue analysis be calculated when real material properties are not available? d) Why some of the materials perform endurance limit, and some don't? Give some examples from each group of material and discuss the reason.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter11: Fracture And Fatigue

Section: Chapter Questions

Problem 11.13P

See similar textbooks

Similar questions

Comment on the following items: a. Why is the material “viscoelastic”? What is meant by this term? b. If more than one material is tested, how did the creep deformation of the different beams differ? Which ones demonstrated the most and least strains? c. Understanding the relationship between instantaneous and delayed elastic response, how does the strain behave at prolonged periods? What do you think would happen after the load is removed?
What are the consequences of strain hardening on ductility? Discuss the influence of strain-hardening on fatigue behavior.
Consider a cylindrical metal 6 mm in diameter and 50 mm long ispulled in tension. It is known that yield strength and elastic (Young’s) Modulus of thematerial are 200 MPa and 100 GPa, respectively, and its Poisson’s Ratio is 0.3.(a) Determine whether the deformation is elastic or plastic when 6000 N is applied.(b) Calculate specimen elongation (∆l) and reduction in diameter (∆d) when 5000 N isapplied? What are the values ∆l and ∆d when the load is released?(c) If necking occurs at a load of 8850 N, determine the UTS of the metal.(d) Calculate the ductility in terms of % E.L. if the length of the specimen at fracturepoint is 56.0 mm.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa
Explain the concept of yield strength and its importance in material testing.
In a tensile test, Load and Elongation are Normalized to Engineering Stress and Engineering Strain . Why?
A cylindrical metal bar with a diameter of 12.83 mm is applied to a load of 17.8 kN. This loadproduces a reduction in diameter of 7.62 μm. The deformation is purely elastic. Determine thePoisson’s ratio of this material if the elastic modulus is 103.4 GPa?
If the material is subjected to triaxial stress, What does each principal stress contribute?
A rod with a length of 1 m and a radius of 20 mm is made of high-strength steel.The rod is subjected to a torque T, which produces a shear stress below the proportional limit. If the cross section at one end is rotated 45 degrees in relation to the other end, and the shear modulus G of the material is 90 GPa, what is the amount of applied torque?
A material has the stress–strain behavior shown in Figure What is the material strength at rupture? What is the toughness of this material?
What is the effect of crosslinks on an elastomer and what is the structural explanation for their effect? What would happen to the amount of stretch, hardness, strength, and creep in an elastomer if the crosslink density were increased?
A load applied to a machine component results in the state of plane stress ?x=80 MPa, ?y=100 MPa, ?xy=60 MPa. The component is made of a brittle high-strength steel that follows the maximum normal stress criterion with ?u=200 MPa. If increasing the load increases each stress component proportionally, determine the percentage increase that can be applied before the component fails.