1. Given the table below: (a) Which will experience the greatest percentage reduction in area? Why? (b) Which is the strongest? Why? (c) Which is the stiffest? Why? Yield Tensile Strain at Fracture Fracture Elastie Modulus (GPa) Material Strength (MPa) Strength (MPa) Strength (MPa) A 310 340 0.23 265 210 100 120 0.40 105 150 C 415 550 0.15 500 310 D 700 850 0.14 720 210 E Fractures before yielding 650 350

1. Given the table below: (a) Which will experience the greatest percentage reduction in area? Why? (b) Which is the strongest? Why? (c) Which is the stiffest? Why? Yield Tensile Strain at Fracture Fracture Elastie Modulus (GPa) Material Strength (MPa) Strength (MPa) Strength (MPa) A 310 340 0.23 265 210 100 120 0.40 105 150 C 415 550 0.15 500 310 D 700 850 0.14 720 210 E Fractures before yielding 650 350

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Examine each of the following and determine the areas they are applicable i.Modulusof Rigidity ii.Poisson’s Ratio iii.Elastic Modulus A copper alloy wire of 1.9mm diameter and 30m long hangs freely from Tower. What will be its extension due to the self-weight of the wire? The specific weight of the copper and its modulus of elasticity are 89.2 kN/mm3 and 90 x 10N/mm2 respectively.Comment on the solution Generally, compressive strength normally considersin all stages in our designs. Explain and state other engineering strength that neededto be taken care of in the process of design. Comment on how it affectsreinforce concrete structure
A wood beam carries the loading shown in the figure. Determine the smallestallowable width b of the beam if the working stress in bending is 10 MPa.
Consider a cylindrical metal 6 mm in diameter and 50 mm long ispulled in tension. It is known that yield strength and elastic (Young’s) Modulus of thematerial are 200 MPa and 100 GPa, respectively, and its Poisson’s Ratio is 0.3.(a) Determine whether the deformation is elastic or plastic when 6000 N is applied.(b) Calculate specimen elongation (∆l) and reduction in diameter (∆d) when 5000 N isapplied? What are the values ∆l and ∆d when the load is released?(c) If necking occurs at a load of 8850 N, determine the UTS of the metal.(d) Calculate the ductility in terms of % E.L. if the length of the specimen at fracturepoint is 56.0 mm.
Figure Q3(a) shows an overhung beam AB that is subjected to point loads, P. The cross section of the beam illustrated in Figure Q3(b), and the material behaves linearly elastic-perfectly plastic with yield strength of 250 MPa. Taking the values of L = 2 m, and a = 1.2 m:a) Calculate the shape factor of the beam cross section.b) Calculate the load, Pp that will cause the beam to collapse (fully plastic) at the most critical location.c) What is the yielded length when the load, Pp in part (b) is applied?
In the figure below, a stainless steel wire is supporting a weight, W. The Yield Strength and Young’s Modulus for stainless steel (Grade 304) is 205 MPa and 190 GPa, respectively. What is the maximum weight, W, in kN that can be supported by the wire if the allowable deformation is 1.3 mm? What is the safety factor relative to the Yield Strength at this allowable deformation condition?