a) What mass of Fe(NH4)2(SO4)2•2H2O(s) is required to prepare a 500 mL solution containing 100 ppm (m:v) in Fe? b) Using this stock solution, what aliquot must be used to prepare calibration solutions, 100 mL volume, of the following concentrations: 0.100 ppm, 0.500 ppm, 2.00 ppm, 4.00 ppm, and 7.00 ppm.

a) What mass of Fe(NH4)2(SO4)2•2H2O(s) is required to prepare a 500 mL solution containing 100 ppm (m:v) in Fe? b) Using this stock solution, what aliquot must be used to prepare calibration solutions, 100 mL volume, of the following concentrations: 0.100 ppm, 0.500 ppm, 2.00 ppm, 4.00 ppm, and 7.00 ppm.

Chemistry by OpenStax (2015-05-04)

1st Edition

ISBN:9781938168390

Author:Klaus Theopold, Richard H Langley, Paul Flowers, William R. Robinson, Mark Blaser

Publisher:Klaus Theopold, Richard H Langley, Paul Flowers, William R. Robinson, Mark Blaser

Chapter15: Equilibria Of Other Reaction Classes

Section: Chapter Questions

Problem 10E: The Handbook of Chemistry and Physics (http://openstaxcollege.org/l/16Handbook) gives solubilities...

See similar textbooks

Similar questions

The mass of K3PO4 needed to prepare 250.0mL of an aqueous solution in which PO4-3 concentration is 0.0550M. The answer is ……………………… How many grams of silver sample is equal to 0.0417 mole of silver The answer is ……………………… When 38.0 mL of 0.1250 M H2SO4 is added to 100 mL of a solution of PbI2, a precipitate of PbSO4 forms. The PbSO4 is then filtered from the solution, dried, and weighed. If the recovered PbSO4 is found to have a mass of 0.0471g, what was the concentration of iodide ions in the original solution The answer is ……………………………… Express 96.342 m using 2 significant figures The answer is ………………………………. The oxidation number of sulfur in (Na2S2O5) is? The answer is ………………………………
The hardness of water (hardness count) is usually expressed in parts per million (by mass) of CaCO3. What is the molar concentration of Ca2+ ions in a water sample with a hardness count of 175mg CaCO3il? How many milliliters of concentrated sulfuric acid, 94.0% (w/w), specific gravity of 1.831 are required to prepare 1 liter of a 0.100 M solution? The solubility-product constant for Ce(IO3)3 is 3.2x1010. What is the Ce3+ concentration in a solution prepared by mixing 50.0 ml of 0.0250 M Ce3.. with 50.00 ml of water?
The solubility of borax, which is made up of sodium tetraborate (Na2B4O5(OH)4 8H2O), was analyzed. The dissolution of borax is: Na2B4O5(OH)4 • 8H2O(s) ⇌ 2 Na+(aq) + B4O5(OH)42–(aq) + 8 H2O(l) A 50 mL saturated solution was prepared. After filtration of solution, 5 mL aliquot was transferred to a flask and titrated using 0.432 M HCl. The endpoint was found to be 4.73 mL of the titrant. Tetraborate anion (B4O5(OH)42-) is a weak base which reacts with HCl like the following reaction: B4O5(OH)42–(aq) + 2 H+(aq) + 3 H2O(l) ⇌ 4 H3BO3(aq) What is Ksp expression for the dissolution? What is the tetraborate ions concentration in the filtrate? What is the molar solubility and Ksp of borax if the titration was done at room temperature (298 K)?
To determine the amount of magnetite. Fe3O4, in an impure ore, a 1.5419 g sample is dissolved in concentrated HCl, resulting in a mixture of Fe2+ and Fe3+. After adding HNO3 to oxidize Fe2+ to Fe3+ and diluting with water, Fe3+ is precipitated as Fe(OH)3 using NH3. Filtering, rinsing and igniting the ppt provides 0.8525 g of pure Fe2O3. Calculate % Fe in the sample.
Nickel sulfate, NiSO 4 , reacts with sodium phosphate, Na 3 PO 4 , to give a pale yellow-greenprecipitate of nickel phosphate, Ni 3 (PO 4 ) 2 , and a solution of sodium sulfate, Na 2 SO 4.. How manymilliliters of 0.375 M N i SO 4 will react with 45.7 mL of 0.265 M Na 3 PO 4 ? . Show balanced chemicalreaction of the problem.
A solution was prepared by dissolving 1210 mg of K3Fe(CN)6 (329.2 g/mol) in sufficient water to give 785 mL. Calculate b) the weight/volume percentage of K3Fe(CN)6, the number of millimoles of K+ in 35.0 mL of this solution, and the ppm of Fe(CN)63-
What mass (in grams) of Na2S2O3 is needed to dissolve 0.44 g of AgBr in a solution volume of 1.0 L, given that Ksp for AgBr is 3.3×10−13 and Kf for [Ag(S2O3)2]3− is 4.7×1013?
A 600.0 mg sample consisting of only CaC2O4and Mg C2O4is heated at 500oC converting the two salts to CaCO3and MgCO3. The sample weighs 465.0 mg. If the sample had been heated at 900oC where the products are CaO and MgO, what would the mixture of oxides weigh? Show the clear and complete solution
describe how you can prepare 500mL of 0.10 M Fe2O3 (159.69g/mol) from the primary-standard-grade solid.
1. A newly discovered iron ore was weighted (5.408 g) and worked up to produced 0.3785 g of ignited Fe2O3 precipitate. What is the percent purity of the iron in the sample? 2. Distinguish between equivalence point and end point.
As part of a soil analysis on a plot of land, a scientist wants to determine the ammonium content using gravimetric analysis with sodium tetraphenylborate, Na+B(C6H5)4−. Unfortunately, the amount of potassium, which also precipitates with sodium tetraphenylborate, is non‑negligible and must be accounted for in the analysis. Assume that all potassium in the soil is present as K2CO3 and all ammonium is present as NH4Cl. A 5.095 g soil sample was dissolved to give 0.500 L of solution. A 150.0 mL aliquot was acidified and excess sodium tetraphenylborate was added to precipitate both K+ and NH4+ ions completely. B(C6H5)4-+K+⟶KB(C6H5)4(s) B(C6H5)4-+NH4+⟶NH4B(C6H5)4(s) The resulting precipitate amounted to 0.269 g. A new 300.0 mL aliquot of the original solution was made alkaline and heated to remove all of the NH4+ as NH3. The resulting solution was then acidified, and excess sodium tetraphenylborate was added to give 0.129 g of precipitate. Find the mass percentages of NH4Cl and…
A technician is setting up a laboratory to standardise ~0.0200 mol dm–3 KMnO4. What mass of Mohr’s salt [FeSO4(NH4)2SO4·6H2O] would the technician be required to weigh out to produce a 5.00 L solution of Mohr’s salt such that 25.0 cm3 aliquots of the salt would require a titre of 20.0 cm3 to standardise the KMnO4 solution?