A wheel rotating with 17 rev/s is uniformly accelerated at 0.5 rad/s² for 5 seconds. It then rotates with a uniform speed for next 7 s. Then it is made to stop in next 15 s. Determine (i)maximum angular velocity; (ii) total angular displacement (Enter only the values in the boxes by referring the units given . Also upload the hand written copy in the link provided) Solution: The maximum velocty in rad/s is The total displacement in rad is

A wheel rotating with 17 rev/s is uniformly accelerated at 0.5 rad/s² for 5 seconds. It then rotates with a uniform speed for next 7 s. Then it is made to stop in next 15 s. Determine (i)maximum angular velocity; (ii) total angular displacement (Enter only the values in the boxes by referring the units given . Also upload the hand written copy in the link provided) Solution: The maximum velocty in rad/s is The total displacement in rad is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw a six-bar linkage mechanism used for holding an industrial stirrer. Points A, B, and E are on a straight line on link 2. Points B, C, and G are on a straight line on link 3. The input link 2 rotates with a constant angular velocity a of 3 rad/s (cw) at the instant. O2=0 (a) Complete the acceleration polygon according to the drawing scale given, and find the angular accelerations Oy, 04, as, and as of links 3, 4, 5, and 6, and the acceleration Ap of point F. The position of link 2 is given as input. Write down the vector loop equations of the linkage for analytical position analysis and identify the unknowns in the equations. Note: Round off all your answers to two decimal places. Dimensions: AB= 40.00 mm BE = 20.00 mm BC = 33.54 mm CG= 33.54 mm CD = 18.03 mm EF = 43.00 mm FG = 29.15 mm
Find the acceleration of points A and B also the angular accelerations of links 3 and 4 using Relative Acceleration Method. Input link has constant angular velocity. Note that the drawing is not in scale. @2=1 rad/s 02 O 2 30° A 3 B (0) 04 02A=4" AB=7" 0204=9" 04B-8"
A piston, connecting rod and crank mechanism is shown in the diagram. The crank rotates at a constant velocity of 300 rad/s. Find the acceleration of the piston and the angular acceleration of the link BC. The diagram is not drawn to scale. 300 rad/s A 600 50 mm 777//// 170 mm
Bar AB is rotating about A with an angular velocity of wAB 2 rad/s counterclockwise. At this instant bar BC is horizontal. Find the Wac and also, velocity of collar C. Note. You must solve the problem in the way that we solved in the class. Use Vg VA+ wX TB/A and express the vectors in Cartesian vector form. Other solutions will not be evaluated. Solve the problem step by step, and clearly show your work. 25 35 mm 170 mm
Find out the velocity of slider D and angular velocity of CD in the mechanism shown below. Take Q1A= Q2B = 2cm; Q1Q2 = 4 cm; CD = 6 cm and wQ,A rad = 1 sec Solve using instantaneous center method. Use CCW direction. 20 QI 1 A Q2 20
use the information to calculate the periodic time of the point
Graphically, draw the entire acceleration polygon and use it to find both the magnitude and direction of a and ace at the instant shown. Also, find magnitude and direction of a2, a3 and 4 when a) The crank angular velocity w₁ is constant at 100 rad/sec CCW. b) The crank angular velocity w3 is 100 rad/sec CCW and accelerating at 25000 rad/sec² Velocity scale: 1 cm: 20 in/sec Acceleration scale: 1 cm: 4000 in/sec² B 0 0 = 45° 7 in 0₂C = 4 in O₂D = 6 in 0,03 = 6 in 2 in
+ G In the above diagram, the wheel starts from rest and rolls without slipping. The force (you don't need the value) causes a constant angular acceleration of 7.112 rad/s2. The radius of the wheel is R - 0.392 m. What is the magnitude of the acceleration of the point at the top of the wheel at time t 1.400 s? This is the point at the outer edge directly above the center of gravity, Gwhere the force F connects to the wheel. Use units of m/s. Don't place units in your answer, 3 o
The general linkage configuration and terminology for an offset fourbar slider- crank linkage are shown in the figure. The link lengths and the values of d, d.d and d..d are defined in the table. For row a, using graphical method, the value the acceleration of pin joint A is Row la b C d le If g 02 002 Link 2 1.4 2 3 3.5 5 3 0₂ Y Link 2 O 792.064 in/sec2 0₂ 291.385 in/sec2 O 1,593 in/sec2 O 1,779 in/sec2 Link 3 14 16 18 10 20 13 25 Link 3 Offset 1 -3 2 1 -5 10 10 Offset 03 Slider position d, d, d d 2.5 5 8 -8 15 -12 25 y B d.d d..d 10 -12 15 -15 -10 24 -4 -50 10 -45 50 100 18 04 = 90° 10 X
Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon method. Note the drawing is not in scale. B 02 @2=1 rad/s 2 30° A 1 3 4 04 02A=4" AB=7" 0204-=9" 04B=8"
(10 points) Crank_Slider2 a WOP, dop Known values: a 0.38 m 3.4 m 20° 68° Problem Statement: Crank OP rotates about fixed axis O, causing slider Q to oscillate in a horizontal track. At the instant depicted, the angular velocity of crank OP is 4 rad/s and its angular acceleration is 6 rad/s?. For that instant, determine the following. The velocity vector of pin P: i+ 1.4283 m/s -0.5199 m/s The angular velocity of rod PQ: The velocity vector of slider Q: The acceleration vector of pin P: 计 The angular acceleration of rod PQ: The acceleration vector of slider Q: i+
The landing gear of an aircraft is the important mechanism retractable. At the instant shown in Figure 1,the crank AB on the small aircraft landing gear mechanism rotates counter clockwise at 15 rpm and accelerates at 4 rad/s². 1.Draw the displacement diagram to a scale 2.Use the relative acceleration method to graphically determine the linear velocity at point E 3.Determine the angular acceleration of the link DC