A wooden beam is loaded by a distributed load w = 7 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1500 mm, L BC = 3500 mm, W=190 mm, Bo = 30 mm, and H=210 mm, ho=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. Steps: Fill the gaps in the "steps" to get some marks from the working- out process. Adaptive marking is still used. (a) (b) hol Bo H B LAB LBC Cross-section W Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam.

A wooden beam is loaded by a distributed load w = 7 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1500 mm, L BC = 3500 mm, W=190 mm, Bo = 30 mm, and H=210 mm, ho=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. Steps: Fill the gaps in the "steps" to get some marks from the working- out process. Adaptive marking is still used. (a) (b) hol Bo H B LAB LBC Cross-section W Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 44P

See similar textbooks

Similar questions

A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a) What is the maximum magnitude of shear force and bending moment, neglecting the sign? Maximum magnitude of shear force, positive value: Maximum magnitude of bending moment, positive value: b) Determine the maximum bending stress and shear stress that occurs in the beam. Maximum bending stress: Maximum shear stress
4. This figure shows a cantilever beam that is subject to a point load and a moment. What is the vertical displacement at the tip of the beam? Assume E = 200 GPa and / = 1560 X 10° mm%. A. 58.7 mm B. 68.9 mm C. 89.0 mm D. 100 mm
A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a)Determine the 2nd moment of area of this cross-section in Figure Q4(b)? b)Calculate support reactions in A and C, remember the sign of the force. Reaction force at point A: x-direction: XA= y-direction: YA= Reaction force at point C: x-direction: XC= y-direction: YC= c)Calculate the equations of shear force V(x) and bending moment M(x). Type the mathematical expressions or constants. Section AB: Section BC:
A wooden beam is loaded by a distributed load w = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1900 mm, LBC = 3100 mm, W=200 mm, B0 = 30 mm, and H = 200 mm, h0=20 mm. Units: use N, mm, MPa as consistent units for all calculations.
The cylindrical tank weights 500 lb. Determine (a) FH, (b) FV, (c) FR and (d) ϴx. Use 2 decimal places in every solved value.
Answers are a) (25/64) mr22 b) (25/32) mr22 Please show solution that involves mass moment of inertia and NOT area moment of inertia.
A cantilever beam carries a varying load as shown in the figure. If E = 200,000 Mpa and I=120×10^6 mm^4 Determine the following. Use Double Integration Method 1. Slope at free end 2. Deflection at 4m from the support
For the beam and loading shown in Figure below, determine the beam deflection at point H. Assume that EI = 8 × 104 kN·m2 is constant. Express your answer in mm and use three decimal places. Indicate the negative sign in your final answer if the deflection is downward.
Problem 1 only, read and see the figure, solve carefully, include the units in every step and draw the diagram. Thanks!
Determine the following: A. The centroid (x,y) B. The moments of inertia about x and y axis. Note: Write the corresponding units and answers should be in three decimal places.
As shown is a cylinder (r=0.8 m,) that is hinged at O. Compute the FR and ϴx. Analyze 1 m length. Use yw = 9.81 kn/m3 . Use 2 decimal places in every solved value, however use the whole value for the computation of volume.
Please refer to the figure below. Determine R in N at point C.