A wooden block of mass m1 3.2 kg and a hollow block of mass m2 = 8.7 kg are connected bý a rope which runs over a friction-less pulley. Assume that the pulley is a solid iron disc with a radius R = 0.3 m and mass M = 5.1 kg. The ramp is wedge- shaped and makes an angle of 0=36°. The coefficient of kinetic friction is 0.29 for both blocks and the wedgeshaped incline. %3D

A wooden block of mass m1 3.2 kg and a hollow block of mass m2 = 8.7 kg are connected bý a rope which runs over a friction-less pulley. Assume that the pulley is a solid iron disc with a radius R = 0.3 m and mass M = 5.1 kg. The ramp is wedge- shaped and makes an angle of 0=36°. The coefficient of kinetic friction is 0.29 for both blocks and the wedgeshaped incline. %3D

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 60P: A uniform solid disk and a uniform hoop are placed side by side at the top of an incline of height...

See similar textbooks

Similar questions

A boy rides his bicycle 2.00 km. The wheels have radius 30.0 cm. What is the total angle the tires rotate through during his trip?
A constant torque is applied to a rigid body whose moment of inertia is 4.0kgm2 around the axis of rotation. If the wheel starts from rest and attains an angular velocity of 20.0 rad/s in 10.0 s, what is the applied torque?
A uniform solid disk and a uniform hoop are placed side by side at the top of an incline of height h. (a) If they are released from rest and roll without slipping, which object reaches the bottom first? (b) Verify your answer by calculating their speeds when they reach the bottom in terms of h.
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
A hollow cylinder that is rolling without slipping is given a velocity of 5.0 m/s and rolls up an incline to a vertical height of 1.0 m. If a hollow sphere of the same mass and radius is given the same initial velocity how high vertically does it roll up the incline?
When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
From the step ladder shown in the figure, sides AC and CE are each 2.44 m long and hinged at point C. Bar BD is a tie-rod 0.762 m long, halfway up. A man weighing 845 N climbs 1.8 m along the ladder. Assuming the floor is frictionless and neglecting the mass of the ladder, find the tension (in N) in the tie-rod.
A roller has a mass of 1,081.8kg, a radius of gyration of 107.3 mm, and is lifted by 2 ropes as shown . If each cable has the following tensions TA =3,195.7 N and TB =3,308.5 N, determine (a) the angular acceleration of the roll? Input your answer with 2 decimal places and make sure it is positive.
As shown in the figure below, a bicycle wheel is at rest against a curb. If the wheel has a radius R, mass M and is at rest against a curb of height h = 0.22R, determine the minimum horizontal force F (in terms of M and g) that must be applied to the axle to make the wheel start to rise up over the step. F = ?
The engine of the bus applies a torque of 328.2 N · m to a wheel of radius 0.538 m. Since the wheel does not slip, the road must be applying a force of static friction to the wheel that produces a counter-torque. Moreover, the bus has a constant velocity, so this counter-torque balances the applied torque. What is the magnitude of the static frictional force?
A pulley with a diameter of 50cm is driven at 960 r/min. What will be the linear speed, in m/s, of a point on the rim of the pulley?