A wrench 0.8 meters long lies along the positive y-axis and grips a bolt at the origin. A force is applied in the direction of <0,2,1> at the end of the wrench. Find the magnitude of the force in newtons needed to supply 100 newton-meters of torque to the bolt.

A wrench 0.8 meters long lies along the positive y-axis and grips a bolt at the origin. A force is applied in the direction of <0,2,1> at the end of the wrench. Find the magnitude of the force in newtons needed to supply 100 newton-meters of torque to the bolt.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 74P: When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of...

See similar textbooks

Related questions

Q: A bolt is tightened by applying a 60 N force to a wrench. If the magnitude of the torque is 120 Nm,…

A: Given data The magnitude of the force is F = 60 N. The torque is given a T = 120 Nm. The angle…

Q: You stepped on the edge of a bicycle wheel (radius 0.622 m) to make it slow down. If you pressed…

Q: Calculate the magnitude of the total torque in the center of a square, giving that the square side…

Q: What is the minimum magnitude of torque that can be exerted on a rigid body by a 100.0 N force…

Q: A small ball of mass 1.5 kg is attached to one end of a 2.00-m-long massless rod, and the other end…

A: Given Data Mass of the ball is m=1.5 kg Length of the rod is L=2.00 m Angle of the pendulum is θ=32°…

Q: An athlete at the gym holds a 3.0 kg steel ball in his hand. His arm is 70 cm long and has a mass of…

Q: The engine of the bus applies a torque of 328.2 N · m to a wheel of radius 0.538 m. Since the wheel…

A: Given that, magnitude of torque provided by bus on wheel = 328.2 N-m since velocity is given…

Q: Calculate the magnitude of the total torque in the center of a square, giving that the square side…

Q: Find the magnitude of the net torque (in N.m) on the wheel shown in the Figure about the axle…

A: Solution: Given that F =36 N a = 5 cm b = 20 cm

Q: A particle is located at F= (4.0i + 3.5j+5.8k) m. A force F = (8.6j – 3.8k) N acts on it. What is…

A: The torque on the particle can be represented as, Here, F and r represent the applied force, and…

Q: An object of mass 0.2 kg is moving in a circle of radius 2 m with translational acceleration a = 5…

Q: A force F =7.2î +2.3k N is applied at the point (3,0,1) m. What is the y component of the torque?

A: To answer the question we will use the formula: Τ→=r→×F→

Q: A truck tire has a radius of 1.06 m, and its center moves forward with a linear speed of 17.1 m/s.…

A: Radius of the tire is r = 1.06 m Linear speed of the center is v = 17.1 m/s Distance of point from…

Q: The 60.1cm diameter disk rotates counterclockwise on an axle through its center. F1=17.5N, F2=43.2N,…

Q: An athlete at the gym holds a 2.0 kg steel ball in his hand. His arm is 70 cm long and has a mass of…

Q: In an Atwood's machine, one block has a mass of 304.0 g, and the other mass of 454.0 g. The pulley,…

Q: A bolt is tightened by applying a 60 N force to a wrench. If the magnitude of the torque is 120 Nm,…

Q: Two fishermen are exerting a force of 200 N on a paddle while rowing in the middle of a lake. If the…

Q: An athlete at the gym holds a 2.0 kg steel ball in his hand. His arm is 70 cm long and has a mass of…

A: Answer:- Given m1 = 2 kg x1 = 70 cm = 0.7 m m2 = 4 kg The centre of mass of the arm is at the…

Q: The magnitude of torque on a particle of mass 1 kg is 2.5 N-m about the origin. If the force acting…

Q: If you lift the front wheel of a poorly maintained bicycle off the ground and then start it spinning…

A: Given:- ω = 0.66 rev/s. t = 11 s. ι = 0.34 kg⋅m^2.

Q: At the gym, someone holds a 5.0 kg dumbell straight out, parallel to the floor. If the person's arm…

A: magnitude of torque is given by r(perpendicular)F = F(perpendicular)r given, F = 5g = 5x9.8 = 49 N r…

Q: When the sum of the external forces and the sum of the external torques on a body are both zero, we…

A: Given that, The sum of external force is zero And the sum of external force is also zero We know…

Q: In unit-vector notation, what is the net torque about the origin on a flea located at coordinates…

A: Given data: F1=6.42 N k^ F2=-4.93 N j^ Net force: F→=-4.93 N j^+6.42 N k^ Position vector:…

Q: While driving an automobile, the driver makes a left turn. To perform this maneuver, the driver…

A: The expression for the torque is written as, Here, F and r represent the force applied by the…

Q: Find the net magnitude torque (in N.m) on the wheel shown in the Figure about the axle through O,…

A: Refer to the figure below : The torque acting on a body about a point is given by the cross…

Q: The propellers on the Titanic have a radius of 23.5 ft and weigh 38 tons each. If the propellers…

A: Given data: The radius of the propellers r=23.5ft Weight of the propellers W=38tons Number of turns…

Q: What is the moment of inertia about the axis of a solid cylinder with a mass of 20 kg, a radius of 5…

Q: In unit-vector notation, what is the net torque about the origin on a flea located at coordinates…

A: Required : The net torque.

Q: The rotor of a lab centrifuge has moment of inertia 0.0113 kg m^2 and spins at 1470 rad/s. If a…

A: The given data are: I=0.0113 kg.m2ω=1470 rad/sF=16 Nr=0.075 m Here, I, ω, F, and r represent the…

Q: If you lift the front wheel of a poorly maintained bicycle off the ground and then start it spinning…

Q: Find the net torque on the wheel in the figure below about the axle through O, taking a = 7.00 cm…

A: Write the equation for torque

Q: An engineer estimates that under the most adverse expected weather conditions, the total force on…

Q: Find the net torque on the wheel as shown about the axle through O, taking a = 10.0 cm and b = 25.0…

A: Consider anti-clockwise direction to be positive The net torque on the wheel

Q: A certain gyroscope consists of a uniform disk with a 50 cm radius mounted at the center of an axle…

A: The distance r from the center of the mass to the ground,

Q: One end of a meter stick is pinned to a table, so the stick can rotate freely in a plane parallel to…

Q: A solid cylinder with a mass of 5.0 kg is rolling down a ramp. If it has a radius of 10 cm and an…

Q: Two forces, F1=100 N (Newton) and F2=20N, are applied on opposite sides of a door's knob at angles…

A: Given:Force,F1=100 NForce,F2=20 NRotation axis ,r=0.8mAngle,θ1=30Angle,θ2=60Find the net torque…

Q: What constant torque must be applied to a 200 lb cylindrical flywheel having a radius of 2 ft in…

Q: One end of a meter stick is pinned to a table, so the stick can rotate freely in a plane parallel to…

Q: In the figure, what magnitude of force F applied horizontally at the axle of the wheel is necessary…

Q: Complete the following statement: When a net torque is applied to a rigid object, it always produces…

A: Torque is a physical quantity which has tendency to rotate a body. Torque is rotational equivalent…

Q: 0.28 m 50.0

Q: Find the net torque on the wheel in the figure below about the axle through O, taking a = 11.0 cm…

A: Given Data: The inner radius is, a = 11.0 cm The outer radius is, b = 25.0 cm. The three forces…

Q: A slingshot is being whirled around in uniform circular motion. Which of the following statements…

A: Slingshot is being whirled around in uniform circular motion.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?
The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4 kg and its radius is 30 cm, as well as the distance from the center of mass to the pivot, what is the rotation rate in rev/s of the disk?
A man stands on a merry-go-round that is rotating at 2.5 rad/s. If the coefficient of static friction between the man’s shoes and the merry-go-round is s=0.5 , how far from the axis of rotation can he stand without sliding?
A constant torque is applied to a rigid body whose moment of inertia is 4.0kgm2 around the axis of rotation. If the wheel starts from rest and attains an angular velocity of 20.0 rad/s in 10.0 s, what is the applied torque?
Can a set of forces have a net force that is zero and a net torque that is not zero?
What three factors affect the torque created by a force relative to a specific pivot point?
Can a set of forces have a net torque that is zero and a net force that is not zero?
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
If the angular acceleration of a rigid body is zero, what is the functional form of the angular velocity?
What is the torque abot the origin of the force if it is applied at the point whose position is:
A solid cylinder of mass 2.0 kg and radius 20 cm is rotating counterclockwise around a vertical axis through its center at 600 rev/min. A second solid cylinder of the same mass and radius is rotating clockwise around the same vertical axis at 900 rev/min. If the cylinders couple so that they rotate about the same vertical axis, what is the angular velocity of the combination?
A wheel 2.00 m in diameter lies in a vertical plane and rotates about its central axis with a constant angular acceleration of 4.00 rad/s2. The wheel starts at rest at t = 0, and the radius vector of a certain point P on the rim makes an angle of 57.3 with the horizontal at this time. At t = 2.00 s, find (a) the angular speed of the wheel and, for point P, (b) the tangential speed, (c) the total acceleration, and (d) the angular position.