A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.2 m, LBC = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) Omax,T = MPa (b) ơmax,C = MPa

A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.2 m, LBC = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) Omax,T = MPa (b) ơmax,C = MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A W18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w = 3.4 kips/ft, LAB = 3.0 ft, LBC = 3.0 ft, and LCD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam.
A W16 × 50 standard steel shape is used to support the loads shown on the beam. Assume P = 11 kips, w = 1.4 kips/ft, a = 32 ft, and b = 11 ft. Determine the magnitude of the maximum bending stress in the beam. Answer:σmax = ksi
A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 50 kN/m, LAB = 1.4 m, LBC = 2.8 m, and LCD = 1.4 m. Consider the entire 5.6 m length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and(b) the maximum compressive bending stress at any location along the beam (enter a negative answer).
A W18x40 standard steel shape is used to support the loads shown on the beam. Assume P= 26 kips, w = 4.6 kips/ft. Lab = 4.0ft. Lbc = 4.0ft, and Lcd = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam
A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 60 kN/m, LAB = 1.2 m, LBC = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer).
An S 380 x 74 section is used as a simply supported beam to carry the uniformly distributed load of magnitude 3W and the concentrated load W. What is the maximum allowable value of W if the working stress in bending is 120 MPa?
A channel shape is used to support the loads shown on the beam. The dimensions of the shape are also shown. Assume LAB=3ft , LBC=9ft , P=2050lb , w=1200lb/ft , b=12in , d=5in , and t=0.875in. Consider the entire 12-ft length of the beam and determine a)the maximum compression bending stress at any location along the beam and b)the maximum tension bending stress at any location along the beam.Answer in ksi, rounded-off to 2 decimal places.
A WT305 × 41 standard steel shape is used to support the loads shown. Assume w = 48 kN/m, LAB = 1.6 m, LBC = 3.2 m, and LCD = 1.6 m. Consider the entire 6.4 m length of the beam and determine:(a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and(b) the maximum compressive bending stress at any location along the beam (enter a negative answer). (c) Calculate the reaction forces at B and E. Forces are positive upwards.
A beam of T-section is supported and loaded as shown in the figure below. The cross section has width b = 2.5in., height h = 3in., thickness t = 0.5in, c1 = 2in, and c2 = 1in. Determine the maximum tensile and compressive stresses in the beam if I = 2.0833 in^4 .
150 x 250 mm rectangle beam carries a uniform distributed load of W kN/m over its entire span. The beam is freely supported at its ends. If the maximum allowable bending stress is 9Mpa and the maximum allowable shearing stress is 1Mpa. Calculate the safe uniform load W(kN/m) Calculate the value of maximum shear (kN)
For the beam section shown below, calculate the nominal flexural capacity (Mn) assuming that the tension force is T=1000 kN, the stress block depth is a=150 mm, and f'c = 40 MPa.
The initial compressive force of a steel column can be determined by using the Euler's Critical Load Formula. The x-axis has an unbraced length of L meters which is fixed at the top and bottom supports to prevent sidesway. The y-axis has an unbraced length of L/2 meters due to the bracing at mid-height. The properties of the column are the following A=8,453mm2 , Ix=178,046,682mm4 , Iy=21,982,846mm4 ,Fy=345MPa. Calculate the minimum length, L of the column in millimeters without exceeding the proportionality limit, fs=328.8MPa. Express your answer in 2 decimal places. Please box the final answer.