The stresses shown act at a point in a stressed body. The stress magnitudes are S, - 70 MPa and Sy = 230 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 52°. Answer: Sn= MPa Snt = MPa

The stresses shown act at a point in a stressed body. The stress magnitudes are S, - 70 MPa and Sy = 230 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 52°. Answer: Sn= MPa Snt = MPa

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 53°.
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
For soil elements shown in the figure, determine the maximum and minimum principal stresses. Also determine the normal and shear stresses on plane AB.
The supported beam in the figure has its cross section and area shown. Determine the Absolute Maximum Bending Stress, draw the stress distribution over the cross section at this location. Also, what is the stress at point C of the cross section?
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
The vertical stress at point P1 due to the point load Q on the ground surface as shown in figure is sigma_{z} According to Boussinesq's equation, the vertical stress at point P2 shown in figure will be
state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx = 170 MPa, Sy = 85 MPa, and Sxy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 48°.
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements (10 marks)