A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.

A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.43P: A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads...

See similar textbooks

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a) Develop an expression for the reactive power Q in terms of ,L, and I, from complex power considerations. (b) Let the instantaneous current be i(t)=2Icos(t+). Obtain an expression for the instantaneous power p(t) into L, and then express it in terms of Q. (c) Comment on the average real power P supplied to the inductor and the instantaneous power supplied.
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
1. a) Find the rms magnitude and the phase angle of ICA in the circuit shown. 2. b) What percent of the average power delivered by the three-phase source is dissipated in the three-phase load?
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
An AC generator having an internal resistance of 2 k*(omega) is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, E = 282 sen (100*pi*t) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.