A y N fixed support at A 10 N/mm 150 mm B X 250 mm 200 mm C 2. Which of the following is the magnitude F, and location L (see force diagram in item 1), of the concentrated force equivalent to the rectangular distributed load? F=2000 N, L = 100 mm + F=2000 N, L = 0 mm F=1000 N, L = 100 mm F=2000 N, L = 100 mm F=1000 N, L = 0 mm 4. Which of the following gives the CORRECT moment equilibrium equation? 500 N

A y N fixed support at A 10 N/mm 150 mm B X 250 mm 200 mm C 2. Which of the following is the magnitude F, and location L (see force diagram in item 1), of the concentrated force equivalent to the rectangular distributed load? F=2000 N, L = 100 mm + F=2000 N, L = 0 mm F=1000 N, L = 100 mm F=2000 N, L = 100 mm F=1000 N, L = 0 mm 4. Which of the following gives the CORRECT moment equilibrium equation? 500 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

• b1 = 300 mm • b2 = 180 mm . d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa •fy=414 MPa • eccentricity = 500 mm Determine the nominal axial load in kN if it is applied at an eccentricity of 200 mm.
Q1 / Determine the resulting displacement of pin B. Assume: A1 = A2 = 900 mm², E1 = E2 = 100 GPa, al = a2 = 12x10-6 / ° C, AT = 35 ° C, h = 1200 mm, 0 = 60 °
The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 0.4 between both collars and the rod determine the maximum supporting force available from friction when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 168.75
A rectangular reinforced concrete beam 350 x 550 mm (b x d) is provided with 3H25 bar (As = 1473 mm2) as compression steel. Determine the area of tension steel needed for the beam to attain its full moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 35 N/mm2and fyk = 500 N/mm2and d’ = 60mm. Take until 2 decimal point for each calculation. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167 As ‘ = (M-Mbal) / 0.87 fyk (d-d’) As = Mbal / 0.87 fyk zbal + As’
The tripod shown is to support a vertical load W and horizontal load P at point D. The legs of the tripod rest on a level rough surface at points A, B and C. If W=150N, P=50N, a = 0.5m, b =0.75m. c=1.125m, d=1.5m, 19. Determine the force acting on leg AD. Determine the force acting on leg BD.
The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 0.4 between both collars and the rod determine the maximum supporting force available from friction when F = 0 and when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 618.75
4. A rectangular reinforced concrete beam 300 x 500 mm (b x d) is provided with 4H20 bar as compression steel. Determine the area of tension steel needed for the beam to attain its full = moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2and fyk = 500 N/mm2and d’ = 50mm.
The strut is supported by a pin atC and a steel wire AB. If the wirehas a diameter of 0.2 in.Determine how much itstretches when the distributedload acts on the strut. Use E =29x106 psi.
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
Given: S1=S2=S3= 2.8 m L1=L2=L3= 6.0 m b = 300 mm h = 400 mm t = 100 mm column = 0.3 m x 0.3 m total ultimate load = 12 kN/m f'c = 20.7 MPa fy = 275 MPa Calculate the positive moment (kN-m) at the interior span bounded by FGKJ.
The short column below is subjected to Pu = 100W kN. . Use f’c = 28 MPa and fy = 415 MPa, Clear cover is 40 mm. Analyze analytically and not using charts. Disregard buckling/slenderness. a. What is the maximum moment Mu (kNm) that can be applied along the x axis
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.