a. A vane shear test was conducted in a saturated clay. The height and diameter of the rectangular vane were 4 in. and 2 in., respectively. During the test, the maximum torque applied was 230 lb-in. Determine the undrained shear strength of the clay. b. The clay soil described in part (a) has a liquid limit of 58 and a plastic limit of 29. What would be the corrected undrained shear strength of the clay for design purposes? Use Bjerrum's relationship for A [Eq. (3.40a)]. Cu(field) OCR = B σο (3.42) 1 (3.45) 0.08 + 0.0055(PI)

a. A vane shear test was conducted in a saturated clay. The height and diameter of the rectangular vane were 4 in. and 2 in., respectively. During the test, the maximum torque applied was 230 lb-in. Determine the undrained shear strength of the clay. b. The clay soil described in part (a) has a liquid limit of 58 and a plastic limit of 29. What would be the corrected undrained shear strength of the clay for design purposes? Use Bjerrum's relationship for A [Eq. (3.40a)]. Cu(field) OCR = B σο (3.42) 1 (3.45) 0.08 + 0.0055(PI)

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Natural Soil Deposits And Subsoil Exploration

Section: Chapter Questions

Problem 3.19P

See similar textbooks

Similar questions

A field vane shear test was conducted in saturated clay. The height and diameter of the vane were 101.6 mm and 50.8 mm respectively. During the test, the maximum torque applied was 0.0168 kN.m Determine the undrained shear strength of the clay?
Soil Mechanics An embankment consists of clay fill for which c′ = 25 kN/m2 and φ = 27° (from consolidated undrained tests with pore-pressure measurement). The average bulk unit-weight of the fill is 2 Mg/m3. Estimate the shear-strength in kPa of the material on a horizontal plane at a point 20 m below the surface of the embankment, if the pore pressure at this point is 180 kN/m2 as shown by a piezometer. a. 133 b. 100 c. 166 d. 200
a. A vane shear test was conducted in a saturated clay. The height and diameter of the rectangular vane were 4 in. and 2 in., respectively. During the test, the maximum torque applied was 230 lb-in. Determine the undrained shear strength of the clay. b. The clay soil described in part (a) has a liquid limit of 58 and a plastic limit of 29. What would be the corrected undrained shear strength of the clay for design purposes? Use Bjerrum’s relationship for λ [Eq. (3.40a)].
a. A vane shear test was conducted in a saturated clay. The height and diameter of the rectangular vane were 4 in. and 2 in., respectively. During the test, the maximum torque applied was 230 lb-in. Determine the undrained shear strength of the clay. b. The clay soil described in part (a) has a liquid limit of 58 and a plastic limit of 29. What would be the corrected undrained shear strength of the clay for design purposes? Use Bjerrum’s relationship for λ
The sand layer shown is 2.5m thick. Beneath the sand layer is a 1.8m thick clay layer, underneath the clay layer is a solid rock. Water table is at depth of 0.9 m below the ground surface. SAND: Ymoist= 23KN/m3 ; Ysat= 21KN/m3 CLAY: Ysat= 23 KN/m3 ; LL= 42% e=0.7 A.) Compute the overburden pressure at mid-clay layer. B.) Find the maximum surface pressure without exceeding a 139.5mm settlement in clay layer if it is assumed to be normally consolidated. C.) If surface pressure is 70kpa and pre-consolidation pressure is 80kpa, find the settlement in clay layer.
A soil profi le consists of a clay layer underlain by a sandlayer, as shown in Figure P7.17. If a tube is inserted intothe bottom sand layer and the water level rises to 1 mabove the ground surface, determine the vertical effective stresses and porewater pressures at A, B, and C. IfKo is 0.5, determine the lateral effective and lateral totalstresses at A, B, and C. What is the value of the porewater pressure at A to cause the vertical effective stressthere to be zero?
a. A vane shear test was conducted in a saturated clay. Theheight and diameter of the rectangular vane were 4 in.and 2 in., respectively. During the test, the maximumtorque applied was 230 lb ? in. Determine the undrainedshear strength of the clay.b. The clay soil described in part (a) has a liquid limit of58 and a plastic limit of 29. What would be the correctedundrained shear strength of the clay for design purposes?Use Bjerrum’s relationship for l [Eq. (3.40a)]. Determine the overconsolidation ratiofor the clay. Use Eqs. (3.42) and (3.45). Use s9o 5 1340 lb/ft2.
A vane shear test was conducted in a saturated clay. Theheight and diameter of the rectangular vane were 4 in.and 2 in., respectively. During the test, the maximumtorque applied was 230 lb ? in. Determine the undrainedshear strength of the clay.
An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 9from consolidated undrained test with pore pressure measurement) The weight of fill per unit volume is 18.64 kN/m3. Compute the stress in kPa at depth of 20 m. Show free body diagram a.21.6 b.372.8 c.192.8 d.62.5
Plz give the correct answer. Compute the intensities of active and passive earth pressure at depth of 8 m in dry cohesionless sand with an angle of internal friction of 30 degrees , and unit weight of 18kN / (m ^ 3) What will be the intensities of active and passive pressure if the water level rises to the level? Take the saturated unit weight of sand as 22kN / (m ^ 3) .
Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (Δσav) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0. 0.4 m, 0.8 m, and 1 m. Use Boussinesq’s solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area
A field vane shear test was conducted in saturated clay. The height and diameter of the vane were 101.6 mm and 50.8 mm respectively. During the test, the maximum torque applied was 0.0168 kN.m Determine the undrained shear strength of the clay? The clay soil described above has a liquid limit of 64 and a plastic limit of 29. What is the plasticity index?