1 Instructions: Show your solutions neatly and orderly.A. Calculate the following DC quantities: Ig, Ico, Vcea, Vcejot) and Iasat)-B. Calculate the following AC quantities: r'e, ru Av, Vout, VCE(of) and icsat).C. Using the values obtained in A and B, draw the dc and ac load lines for RC-coupled amplifier inthe given figure. Indicate the Q point on the graph.Voc 24 VR- 330 knR- 1.5 kfiCnB = 150CautR- 1.5 knV = 50 mVpp

DC base current (IB) IB=VCC-VBERB =24-0.7330000 =70.60 μA Quiescent Collector Current (ICQ)…

A. Calculate the following DC quantities: la, Ica, Vaa, Vaulom and Icisat)- B. Calculate the following AC quantities: r, ru, Av, Vouts VCE[of}) and içquat)- C. Using the values obtained in A and B, draw the dc and ac load lines for RC-coupled amplifier in the given figure. Indicate the Q point on the graph.

A. Calculate the following DC quantities: la, Ica, Vaa, Vaulom and Icisat)- B. Calculate the following AC quantities: r, ru, Av, Vouts VCE[of}) and içquat)- C. Using the values obtained in A and B, draw the dc and ac load lines for RC-coupled amplifier in the given figure. Indicate the Q point on the graph.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

For the BJT amplifier circuit of figure below with the following parameters:β = hfe ≈ 250, re= 20.3Ω, and ro = 1/hoe ≈ ∞ Ω, Zb= 50.26KΩ determine:(a) Draw the Ac equivalent circuit in re- model and hybrid model.(b) hie, , Zi , and Zo'(c) Av using h- model.(d) Avs and ac output voltage
Draw the dc and ac equivalent circuits (menu steps 1 and 3) for the common-source amplifier as shown .
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Vs=100 mV peak-to-peak, 1 kHz sine signal, Kn=0.4mA/v^2 ,Vt=1V , λ=0.01V^-1 Make the DC analysis of the above given mosfet amplifier circuit. Simulation to tableWrite down the measured values and mathematical calculation results. (The valueswith the units.)DC Parameters ,Measured value ,Calculated ValueVGETCVGSVDVDSIDb. Draw the small signal model for the AC analysis of the circuit. Find the gm, ro, Av values.c. Show the Vs input signal and the Vo output signal of the circuit on the oscilloscope. Volt/div of channels andSpecify time/div values.
A.What is the phase relationship between the AC input and output voltages in a common emitter amplifier ? What is the reason for the phase reversal ? B.What is the phase relationship between the ac input and output signal voltages in conmmon bas amplifier?what is the reason?
Consider the common-source amplifier shown in Figure P11.50. The NMOS transistor has KP=50 μA/V2, L=5 μm, W=500 μm, Vto=1 V and rd=∞.a. Determine the values of IDQ, VDSQ and gm. b. Compute the voltage gain, input resistance, and output resistance, assuming that the coupling capacitors are short circuits for the ac signal. Repeat Problem P11.50 for an NMOS transistor having KP=50 μA/V2, W=600 μm, L=20 μm, Vto=2 V and rd=∞. Compare the gain with that attained in Problem P11.50.
Design a Single-Stage Common Emitter Class A Amplifier Specifications:Voltage Divider Bias Circuit Supply: Any value from 10Vdc to 24VdcLoad: 1kΩVoltage Gain: Any value from 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50mVp-pTransistor: Si, β = 75 • Base-Collector capacitance = 8pF • Base-Emitter Capacitance = 25pF a) compute for the biasing resistances.b) determine the dc transistor terminal voltages and transistor currents.
For a series ac circuit having resistive and reactive components, How do you determine the active power consumed? Give two equations for calculating the active power.
Draw the equivalent circuit for a common-emitter bipolar transistor amplifier andderive suitable formulae for the amplifier current gain, voltage gain and power gain.Neglect bias,decoupling and coupling components
Topic: Input and Output Characteristics of Transistor in Common Base Configuration Answer in 2-3 sentences each. Need a kind tutor that will do it for me. Thank you! 1. What are the applications of the common base (CB) configuration? 2. What are the output and input impedances of CB configuration?
Coonsider the common emitter amplifier shown in figure below. Assume a β of 100, VBE = 0.7V, VT = 25mA and VA = 100V. Draw an equivalent DC model and determine the rπ, transconductance (gm) and ro. Draw an equaivalent AC model using the small-signal model Find an expression for vbe and vo in terms of the input voltage
For the circuit in the figure below, consider rd = 100kΩ and determine the values of: a) VGS, VDS, ID b) RIN, ROUT c) gm and AV gain