a. Estimate the torsional yield strength of the wire. b. Estimate the static load corresponding to the yield strength c. Estimate the scale of the spring. d. Estimate the deflection that would be caused by the load in part (b). e. Estimate the solid length of the spring. f. What length should the spring be to ensure that when it is compressed solid and then released, there will be no permanent change in the free length?

a. Estimate the torsional yield strength of the wire. b. Estimate the static load corresponding to the yield strength c. Estimate the scale of the spring. d. Estimate the deflection that would be caused by the load in part (b). e. Estimate the solid length of the spring. f. What length should the spring be to ensure that when it is compressed solid and then released, there will be no permanent change in the free length?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM: 4 A helical spring is made from a wire of 11 mm diameter and is of outside diameter 101 mm. The spring has 8 numbers of active coils. If the permissible stress in shear is 480 N/mm2 and the modulus of rigidity is 87 KN/mm2. Find the axial load which the spring can take and the deflection produced.
A spring sustains 200 ft-lb of energy with a deflection of 3’’. Assume that the mean coil diameter is 7 times the wire diameter and that the allowable stress is 100ksi. Determine the wire diameter.
Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate of 0.209 kg ∕mm and the other two have equal spring rate of 0.643 kg ∕mm. Find the deflection.
Find equivalent spring stiffness
In a compound helical spring, the inner spring is concentric with the outer spring, but is 9 mm shorter. The outer spring has ten coils of mean diameter 24 mm, and the wire diameter is 3 mm. Find the stiffness of the inner spring if an axial load of 150 N causes the outer spring to compress 18 mm. If the mean coil diameter for the inner spring is 15.94 mm, find the wire diameter of the inner spring when it has eight coils. Both the springs are made of the same material having G = 77 GPa.
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
Using superposition. Find an equation describing the deflection and the spring reaction force.
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: mean coil diameter = 100 mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: mean coil diameter = 75 mm No. of turns = 20Both the springs are of equal initial length when unloaded. Ifthe working stress for each spring is to be same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following:a. Diameter of steel wire for inner spring. b. Stiffness of inner springc. Stiffness of the compound spring. I need answer ASAP. Thank you!
A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?
A helical spring is provided with a rigid plate at each end. A bolt passes through the spring and the end plates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and the plates are each 25 mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire (take E = 200 GPa and G = 80 GPa).
For the helical compressive spring under fatigue load must meet
Find the equivalent spring constants of the following bending (angular and linear deflection)