Answered: a1) Draw BMD,SD,AFD(axial force…

Engineering

Civil Engineering

a1) Draw BMD,SD,AFD(axial force diagram) for the following questions. 15 ft 15 0 25 k 10 t 12 k 10ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4-10 Compute M, and check As.min for the beam shown in Fig. P4-10. Use f'. = 5000 psi and fy =…

Q: Q) Determine the elastic and plastic moment of resistance of the RC beam. The beam is a trapezoid…

Q: 6 kNI SkN/m -1.5m- 15m

Q: A 12m, I !!!2 Ar 10 kN/m 2m 2I I''² "I E = constt

A: Given data : Loading and dimensions are given Reactions at pin support are taken as Redundants. The…

Q: For the same beam and loading shown, what is the slope at Point A?

A: We will be using method of superposition Slope at any point will be algebraic sum of all the…

Q: The cantilevered W530 x 150 beam shown is subjected to a 7.5-kN force F applied by means of a welded…

A: Given:- The cantilevered beam W530×150 beam is given The magnitude of the force applied = 7.5 kN…

Q: Determine the shear reinforcement spacing of the beam shown within and beyond 2h from the support…

Q: Draw SFD and BMD for given loaded beam. 5 kN 10 kN 3 kN/m A E 4 m 3 m B C 1 m D 3 m 1 m

A: Consider the figure,

Q: Calculate the SF and BM at critical points and draw SFD and BMD for the carſtilever beam shown in…

A: Explained below

Q: Design the beam for flexure using the maximum moment. Assume b=300mm, h=425mm, cc=40mm, stirrups…

A: b=300 mmh=425 mmcc=40 mmstirrups diameter=12 mmd=425-40-12-(282)d=359 mmTension bar diameter=28…

Q: A triangular beam having a base width of 433 mm has a total depth of 776 mm. It is reinforced with…

Q: لما اننا A A < 10m ADE C C₂ 6 KN ↑ 10m B

A: Free body diagram:- A free body diagram, also known as a force diagram in engineering, is a…

Q: Q1 F₁-9kN F₁-12kN 4m 3m 4m 5m 12 F₂ = 5kN F₂-15kN Replace the five forces shown above with a single…

A: Given :

Q: Using IPE shape, design the beam shown. Neglect Vy. F = 13KN, L = Im, Gall = 120M Pa. M2 A В C L

Q: Q2:A continuous beam have 'section shown in Fig (2-a), and clear span of 6 m as shown in Fig (2-b).…

Q: 1. Design a column base plate to support an axial load of 1000 kN. Fp = 0.25fc, Fy = 248 MPa, fc =…

A: The question is based on the column in the shape of the I section. The axial load on the column,…

Q: 7k/f 12'

A: Given Data: UVL=7k/ft Span L=12' To find Vmax

Q: A 550mmx800mm column reinforced with 12 pcs of D20mm (3 bars each on outer ends). The column carries…

A: Solution: Given: column = 550mmx800mm 12 pcs of D20mm (3 bars each on outer ends). ultimate load of…

Q: Determine the maximum factored load Wu that the beam can carry. The beam has dimensions b =250mm,…

A: Solution: Given: Span = 7.3 m b =250mm d=425mm fc’=30MPa Grade 40 rebars. fy = 280 MPa

Q: Determine the design flexural strength in ft kips of a W12 x 35 of A242 (Fy = 50ksi) steel subject…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Draw SFD and BMD for given loaded beam. 5 kN 10 kN ÎŢª 3 kN/m B 4 m 3 m 1 m C 3 m E D 1 m

A: Given:- To find:- Shear force and bending moment diagram

Q: Design a rectangular tied column with the long side equal to two times the length of the short side.…

Q: Calculate the magnitude of the tension T and the angle for which the eye bolt will be under a…

A: For the given eye bolt:

Q: Draw the shear and moment diagram and determine the Vmax and Mmax Oof the cantilever beam shown…

Q: A rectangular beam has b 300mm and an effective depth of 490mm. Concrete compressive strength fe =…

A: Note - factored loads are not mentioned to consider. So beam is designed for maximum moment value as…

Q: Gh b36 cm, I-beam Ne 12.

A: given h =9 cm , b = 6cmCordinater of cross sectional centroid Area =bh2 9×62=542Area…

Q: Homework 2-2.1 13k 9k A D 50° mm 6 7B 50° 6' 2-2.1-1 2-2.1-1 Find the axial forces in bars BE and BC…

Q: Q3. Replace the loading system by an equivalent resultant force and couple moment acting point A.…

Q: 1) Show shear force diagram and bending moment diagram for the loading shown below 15 kips 8 kips w…

Q: *6-124. Using the techniques outlined in Appendix A, Example A.5 or A.6, the Z section has principal…

Q: Problem 12: A 16-in x 20-in concrete column (Fig. 7) is subjected to the following loads: PD (Dead)…

Q: 2/75 If the resultant of the loads shown passes through point B, determine the equivalent…

A: - In y direction : Ry = -10 + 4 - 12 = -18 kips - In x direction : Rx = 0 - Moment at point O : Mo =…

Q: Design a simply supported rectangular reinforced concrete beam. 60KN PLI W. 17KN/m Vu (L.L) h 600mm…

A: LL=17KN/mP=60KNBending moment for this beam=wabl+wl28B.M=60×2×4.56.5+17×6.528=172.858KN-mas per is…

Q: O Q2) Determine the ultimate load Pu that can be applied at eccentricities ex-100mm and ey=125mm for…

A: Given data:- Eccentricity on x-axis, ex = 100 mm Eccentricity on y-axis, ey = 125 mm Diameter of…

Q: The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E - 29,000 ksi;…

A: Given, E = 29000 ksi I = 843 in4 w = 6.7 kip/ft or 0.558 kip/in

Q: PROBLEMS 10.1. Determine the allowable ultimate axial load on a rectangular short tied column 12 by…

A: Given: Dimension of rectangular short tied column = 300 x 450 mm Number of reinforcement bars = 6…

Q: Determine the maximum permissible ultimate uniform load (Wu) for a 7m simply supported beam having a…

Q: A 300mm by 450mm rectangular beam carries a uniform ultimate load and concentrated load as shown.…

A: Only left reaction is calculated as asked.

Q: Calculate the SF and BM at critical points and draw SFD and BMD for the cantilever beam shown in the…

Q: Draw SFD and BMD for the cantilever beam subjectedto loading as shown below. 40KN 0.5m, 30° -20KN/m…

Q: Q1. Given: f'c= 24MPA fy3 420MPA Design the beam for the maximum ultimate shear force. Beam width,…

A: Given Data: Characteristic strength of Concrete=24 Mpa fy=420 Mpa Beam width, b=500 mm Beam…

Q: simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of…

Q: Find the internal forces and moment acting at point A in the beam. The vertical reaction at the…

A: Schematic diagram of the given problem:

Q: Design the positive moment of the beam shown below, determine the number of 20mm diameter bars and…

Q: 02) Based on shear considerations only, calculate the total factored löad the Beam shoWH below can…

Q: Determine the required stirrups spacing, in mm at the critical section Given: Width of the beam =…

A: Solution: Given Data Width of the beam=300 mmTotal depth=600 mmclear concrete cover= 40 mmfc=28…

Q: Determine the design compressive strength (kips) of a A36 steel column, W 10 X 33 with a total…

Q: A30in.*30 in. Frame column of an intermediate reinforced concrete moment frame. The column has been…

Q: QUESTION 5 TT Pi kips P2 kips 2'-0"- 4'-0" 6'-0" The boam shown is subjected to two point loads P1 =…

Q: Find the maximum shear for the given beam below. 3K/ft ... 12K IGK 16K 2K/ft b T Fotototatot 8' 4'…

Question

solve please urgent

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the diameter of a spiral column axially loaded with 1100 kN dead load, and 1000kN live load. Use 28 mm diameter bars, 10mm spirals and steel ratio of 0.02. fc’ = 28MPa; fy=414MPa.
A tied column shown below is bent in a single curvature about the y-axis. Determine the following if K = 1.0, the column is braced against sidesway, fc’ = 27.6 MPa, fy = 414 MPa, Ec =4700√fc′.a. Critical load ( Pc ) using Euler’s formulab. Moment magnification factor, δbc. Equivalent eccentricity of the column section, e
A wide flange A992 steel column has a length of 4.6 meters and pinned ends. If Sx=895x103 mm3, Sy=129x103 mm3, d=358mm, bf=172mm, A=7226 mm2, Fy=345MPa, Determine the classification of the column.
A W8x35 steel column has unsupported length of 8m. Using A36 steel, compute for the ultimate axial load capacity (in kN) if both ends are a.) PINNED b.) FIXED? Neglect local buckling. W8x35 Properties A = 6645.15mm^2 lx = 52.45 x 10^6 mm^4 ly = 17.69 x 10^6 rx = 88.9 mm ry = 51.56mm
Calculate the ultimate axial load capacity of a round spiral column having a diameter of 450mm reinforced with six 25mm bars having fy=276 MPa. Assume fc’=34MPa.
Please Answer it fast on Sheet of paper. F1=1.5KN ,F2=3.8KN, a=3.6m ,b=2.0m ,c=1.3m. You need to find Forces in member (CH,AH and CD) And whether it's +ve or -ve.
Check the safety of the section shown in Figure 2 below, using the Bresler Reciprocal Load method, where the section is subjected to a factored axial compression force and bi-axial moments as shown, giving that fc’ = 35 MPa, fy = 400 MPa, design cover (dc)= 50 mm. If the section is unsafe, what are your recommendations to increase the section capacity? Pf = 1 850 kNMfy = 200 kN.mMfx = 135 kN.m
Calculate the required spacing of 10-mm U stirrup in a rectangular beam with b = 280 mm and d = 440 mm at a section where Vu = 250 kN. Use fc = 20.7 MPa and fy=276 MPa.
: A W8 x 35 steel column has an unsupported height of 8 m.Using A-36 steel with Fy =248 MPa and E = 200,000 MPa. Compute the allowable axial load that the column couldcarry: If both ends are fixed, If both ends are pinned, and If one end is fixed and the other end is pinnedProperties of W8x35:A = 6645.15 mm2Ix = 52.45 x 106 mm4Iy = 17.69 x 106 mm4rx = 88.9 mmry = 51.56 mm
d(mm)=125 q(kN/m)=3.0 F(kN)=2.0 T allow(MPa)= 2.5
a symmetrical cross section of a reinforced concrete I-beam has a value of fc=26.92mpa and fy=414mpa calculate the nominal capacity based on the manimum steerl area for a tension controlled condition. b=493mm d=717mm t=131mm web thickness=131mm t=131mm
4. A rectangular reinforced concrete beam 300 x 500 mm (b x d) is provided with 4H20 bar as compression steel. Determine the area of tension steel needed for the beam to attain its full = moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2and fyk = 500 N/mm2and d’ = 50mm.