A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPa). The shear studs to be used have an ultimate stress capacity of 415MPa and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.

A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPa). The shear studs to be used have an ultimate stress capacity of 415MPa and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.8.1P

See similar textbooks

Similar questions

Design the shear reinforcement of the beam loaded as shown using WSD with fc’ = 20.7 MPa and fy = 276 MPa, fs = (fy/2)
a 450mm diameter concrete spiral column is to be designed to support a factored axial load of 3170kn. clear bar cover is 40mm and tge aggregate soze is 25mm. use nscp 2010 with fc'= 28mpa, fy= 414mpa for longitudinal steel, fyt= 414mpa for spiral steel. limit the gross percentage to 2%. which of the following most nearly gives the clear spacing of the main longitudinal reinforcements in mm.
A 300mm by 450mm rectangular beam shown is loaded with ultimate distributed load Wu = 25kN/m over the whole span and ultimate concentrated load of 100kN at the right end. An internal hinge is provided at B so that the beam is statically determinate. The compressive strength of concrete is f'c = 21MPa, yield strength of steel is fy = 415MPa, rebar diameter is 25mm, concrete cover = 40mm, and diameter of strength of stirrups = 10mm. What is the ultimate moment capacity necessary area of tension reinforcement to support maxixum negative moment in the beam in mm^2?
Design the lightest A992 W section possible for the temporary construction loading only. Tkae the beam span to be 24-ft and simply supported. These typical floor beams are 5 feet on the center. The concrete slab is 4 inches, normal weight, f'c = 4ksi and will be placed directly on the beam. Assume that the formwork and the beam self-weight is 10 psf. Apply the concrete ponding factor that steel deck institute (SDI) recommends during the concrete placement and treat the concrete as live load. Take the additional live load during the construction as 20 psf. Assume that the beam has continuous support support along its compression flange. Check the beam for flexure, shear and a maximum LL deflection of L/360.
1. A rectangular reinforced concrete beam has a length of 7.5 – 10.5 m. It is supported with a hinged at one end and a roller 2m from the other end. The width of beam is 350 mm and the overall depth is 550 mm. The beam is reinforced with 5D25 tensionreinforcement and 2D25 compression reinforcement located at 60 mm from the outermostfiber of the beam. The concrete strength fc = 28 MPa and steel yield fy= 390 MPa. Determinethe following:a. Sketch the beam and its cross sectionb. Stress in the compression steel.c. Moment capacity of the beam.d. Factored uniform load throughout the entire span of the beam that could carry.
A simply supported reinforced concrete beam has an effective span of 6 m with effective depth d = 450 mm and width b = 300mm . The imposed loading is 20 kN/m and the dead load (inclusive of self-weight) is 12 kN/m. The concrete is grade C25 (f = 25 N/mm²) and high yield steel (f_{y} = 500N / m * m ^ 2) is specified. a) Produce a sketch showing the beam span with design loading and cross section.
A rectangular plain concrete beam section, 250x500 gross dimension, is cast using a concrete strength fc’ = 30 MPa. Assuming the concrete to crack at a tensile stress equal to 3.28 MPa, determine the magnitude of a concentrated load, excluding its own weight, at midspan that the beam can carry before it cracks if it is on a simple span of 5 m. Concrete weighs 24 kN/m3. Use Mmax=wL/4.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f’c = 28 MPa fy = 276 MPa Aps = 800 mm2 Ds = 10 mm Dm = 18 mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250 kN
Design a one-way slab of 5m x 6m size to carry a floor finish load of 3 kN/m² and a superimposed dead load of 7 kN/m². The grade of concrete used is M20 and the steel used is Fe415. Take the clear span of slab as 5m.
a floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. the floor supports a service live load of 2.1 kPa. using f'c =21MPa, rebar strength fy=415 MPa, calculate the following if a typical interior beam is reinforced with 3-16-mm dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. nominal moment capacity (kN.m) of a typical interior beam in positive bending considering T-beam geometry. a. 96.66 b. 86.99 c. 91.10 d. 81.99 2. maximum factored uniformly distributed load (kN/m) a typical interior beam can sustain against positive bending. a. 30.93 b. 27.83 c. 26.23 d. 29.15 3. maximum service superimposed dead load in kPa. a. 17.73 b. 11.08 c. 16.52 d. 14.77
(a) The detached servant room of a quarter is having internal size of 3.0mxx4.50m. It is to be covered by a roof of RCC. The dead load on roof 4.5kN//m^(2) and the live load is 1.50kN//m^(2) Design the slab by I.S. Code method. Assume grade of concrete as M25 and grade of Steel as Fe415.
A T‐beam has the following properties:Flange width, bf = 820 mmFlange thickness, t = 100 mm Width of web, bw= 250 mmEffective depth, d = 470 mm concrete strength f’c = 20.7 MPa steel strength, fy = 414 MPaDetermine the required tension steel area for the following conditions:A) MDL = 150 kN.m, MLL = 120 kN.mB) MDL = 175 kN.m, MLL = 190 kN.m