1. 3. -

Q: A cantilever beam is loaded with a uniformly distributed load of kips/ft, as shown in Figure below.…

A: Given: Required : Slope at free end

Q: Use the " Double Integration Method" Calculate the maximum deflection if El = 400 000 kNm^2 Note:…

A: Given: Required : Maximum deflection

Q: A circular surface area 200 cm² is inclined to the x and y axes such that the unit vector normal to…

A:

Q: To determine the BOD5 of a waste water sample, 5, 10 and 50 ml aliquots of the waste water were…

A: Wastewater dilution volume=300 mL,To Find-The value of the average BOD5 of the wastewater.

Q: A footing 3.0 x 3.0 m carries a net foundation pressure of 130 kPa at a depth of 1.2 m in a deep…

A: Size of footing=3m x 3m , Net Foundation Pressure , qn = 130kPa , Depth = 1.2m , Unit weight of sand…

Q: Q.1\B) Find the concentrated force due to seismic load at the top of structure (applied at roof) of…

A: Given; Building Height: 75m Assume, Seismic Zone: Zone 3 (moderate seismicity) Importance Factor:…

Q: A two lane single carriage-way is to be designed for a design life period of 15 years. Total two way…

A:

Q: he following is a section of a precedence diagram with contiguous activities. Using the given lag…

A: Find the Calculation methods below: Early Start -- For the first activity, the Early start is 0,…

Q: Write shear and moment equations for the beams in the following problems. In each problem, let x be…

A:

Q: Problem 4. A small community with a population of 25,200 is seeking your services as a consulting…

A: MPN100 = No. of +ve tubes×100ml of sample in -ve tube×ml of sample in all tubeNo. of +ve tube =…

Q: soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was…

A:

Q: Use the moment distribution method to analyse.

A: L = 4 m H = 4 m E = 2475000 kN/m2 I = 0.081 m4 w = 45 kN/m

Q: For the beam shown whose rectangular cross-section is identical with base 350mm and height 750mm,…

A: The loading diagram is shown below. Cross-section b = 350 mm h = 750 mm The reactions have to be…

Q: 6-71. Determine the absolute maximum moment in the beam due to the loading shown. 40 kN 20 KN 25 KN

A: When the function reaches its absolute maximum, it obtains its greatest value. Similarly, an…

Q: The intensity of pressure developed by surface tension of 0.075 N/m in a of water of 0.075mm…

A:

Q: If R is the radius of a circular curve, then the versine on a chord of length C is given by (a) (c)…

A:

Q: If an industrial plant discharges an effluent with a solids concentration at a rate of 5000 lb/day,…

A: An industrial plant discharges an Total solids concentration in the effluent = 5000 lb/day…

Q: A national highway passing through rolling terrain in heavy rainfall area has a horizontal curve of…

A: Speed V=80 kmph Pavement width w=7 m Centrifugal acceleration α=0.52 m/s2 Radius R=450 m Length of…

Q: A strip footing 1.5 m wide is located at a depth of 0.75 m (equal to the foundation thickness) in a…

A: Width of strip footing = 1.5m , Depth = 0.75m = Thickness of foundation , Unit weight of sand =…

Q: soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was…

A:

Q: question • Find the support Jeautions (for A and B) Neglect Beam weight D I got: RA= 12,50ON, RB =…

A:

Q: 23. Find the perimeter of the polar curve r = 4 sin 0. a. 4π b. 8 c. 16x d. 2π 24. A helical spring…

A:

Q: Situation 15 - Refer to the beam shown in the figure. Given: a=1m w = 18 kN/m P = 30 kN Flexural…

A:

Q: .. For a sleeper density of (n+5), the number of sleepers required for constructing a broad gauge…

A:

Q: Q1/ Draw shear force diagram and bending moment diagram of the beam shown in figure 1 below. 45KN 6m…

A:

Q: 6-69. Determine the maximum moment at C caused by the moving load. 12 kN Bla 1 m -0.5 m 8 m 4 m B

A: The below beam figure is shown,To determine:-The maximum moment at C caused by the moving load.

Q: Trial Question For the following particle size distribution, calculate the efficiency of a Lapple…

A: Given; μg =0.06 kg/m.hr  = 1.67×10-5 kg/m.sW = 0.25D = 0.250.5 = 0.125 m

Q: Problem 1) A simply supported beam is loaded as shown in Figure 1-A. Use E = 40 MPa and I = 5 x 10⁶…

A:

Q: A y 6 ft B + 5 kips/ft El= constant 6 ft

A:

Q: 4 kN -3m- +15m+15m+ 20 kN/m D 30 kN -1.6 m- 0.8 m B -3m- B 4 kN

A:

Q: Situation 12- Wooden planks 300 mm wide by 100 mm thick are used to retain soil soil exerts a…

A:

Q: The equation of motion of a particle on a straight path is S = t³ - 3t, where s is displacement in…

A: Given;The equation of motion of a particle on a straight path is S=t3where 'S' is displacement.t = 3…

Q: FOR THE GIVEN PROPERTIES DESIGN THE REINFORCEMENT d': 15 mm 400 mm b d 580 mm 27 MPa OF BEAM OF…

A: d'=75 mmb=400 mmd= 580 mmf'c=35 Mpafy=320 MpaMu=10×108 NmmTo design - Reinforcement -a) NSCP 2001…

Q: A 2-span beam is loaded as shown. Assumed El is constant, use SDM. Show all equations including the…

A: Determine the absolute moment at C and B using Slope-Deflection Method.

Q: An aquifer confined at top and bottom by impermeable layers is stratified into three layers as…

A:

Q: Draw shear force diagram and bending moment diagram of the beam shown in figure 2 below. Then…

A:

Q: Given an AADT of 11 000 for a 2-lane highway and an 85th percentile Vehicle operating speed of…

A: AADT = 11000 vpd 85th percentile speed = 50 kmph

Q: Q-1: Figure-1 shows a 4.5-m-high retaining wall. The wall is restrained from yielding. Then find,…

A: Given;  4.5-m-high retaining wall.  Above groundwater table c' =0ϕ' = 35°γ = 15.7 kn/m3Below…

Q: A dry sand is placed in a container having a volume of 0.0089 cm³. The dry weight of the sample is…

A: volume = 0.0089 cm3. The dry weight of the sample = 0.011 gramsthe combined weight of the soil plus…

Q: The press plungers of a Bramah (hydraulic) press is 40cm² in cross-section and is used to lift a…

A: A press plunger-Area A = 40 cm2= 40x10-4 m2Mass m=800 kgPump plunger area=0.02 m2To Find-The minimum…

Q: 2. A concrete column and cantilever beam as shown P lm The known loads: = 600 kN Pp PL = 400 KN fc'…

A: Given; PD = 600 KN PL = 400 KN fc' = 30 Mpa fy = 420 Mpa

Q: An eight-lane freeway section is designed to have a lane width of 12 ft, right-side shoulder width…

A: Given; Lane width = 12 ft. Right-side shoulder width = 3 ft. and 3 ramps over a 2- mile- long…

Q: Determine the magnitude of the maximum absolute value of the shear force for the beam and loading…

A: Determine the maximum absolute shear force for the beam.

Q: A car is traveling up a 1.5% grade at 65 mi/hr on good, wet pavement. The driver brakes to try to…

A: Given; Grade: 1.5% (or 0.015 as a decimal) Initial speed: 65 mi/hr Reaction time: 1.5 seconds…

Q: 2.45 La barra rígida ABC está suspendida de tres alambres del mismo material. El área de la sección…

A: Given question is  " The rigid bar ABC is suspended from three wires of the same material. The…

Q: Solve the following beam by the conjugate beam method, calculate its maximum deflections, write the…

A:

Q: Q4/ The pressure drop in a certain length of 0.3 m horizontal waterline is 68.95 kPa when the mean…

A: Horizontal waterline length =0.3 m, Pressure drop=68.95 kPa, Mean velocity V=4.5 m/s, Water…

Q: What is the angle of the resultant of the 2 forces below? Give the answer in degrees to one decimal…

A: Angle of resultant force can be calculated as Given forces F1=3 kipsF2=5 kips

Q: Q2/ If the turbine extracts 400 kW from the flow, what flowrate must be passing through the system?…

A: L1=600 md1=0.6 mL2=600 md2=0.6 mf=0.020P1=P2=atmospheric pressureZ1-Z2=105-30=75V1=0Power of…

Q: Question A circular primary clarifier processes an average flow of 5005 m³/d of municipal waste…

A: Average flow = 5005 m3/dOverflow rate = 35 m3/m2/dThe diameter of the clarifier is =?