Abar having a length of 5 in and cross-sectional area of 07 in is subjected to an axial force of 8000 b Figure - Part A If the bar stretches 0.0010 in determine the modulus of elasticity of the material. The material has linear elastic behavior (1) Submit VAE Ivec Provide Feedback Previous Answers Request Ans X Incorrect Try Again; 4 attempts remaining ki

Abar having a length of 5 in and cross-sectional area of 07 in is subjected to an axial force of 8000 b Figure - Part A If the bar stretches 0.0010 in determine the modulus of elasticity of the material. The material has linear elastic behavior (1) Submit VAE Ivec Provide Feedback Previous Answers Request Ans X Incorrect Try Again; 4 attempts remaining ki

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear elastic behavior.
A bar has a length of 200 mm and cross-sectional area of 7500 mm2. Determine the modulus ofelasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm.The material has linear-elastic behavior.
A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P = 50 kN. The elongation of the rod is d = 1.40 mm, and its diameter becomes d = 19.9837 mm. Determine the modulus of elasticity and the modulus of rigidity of the material. Assume that the material does not yield.
The deck of a bridge is made up of 12 mm thick steel plates 2 m long by 1·2 m wide. Under load, the plate is subject to tensile forces of 7·5 kN longitudinally and 6 kN across the width. Determine the change in the thickness of the plate under this load regime. Modulus of elasticity = 210 GN/m² and Poisson’s ratio = 0·3
1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 GN/m?. [80 MN/m²; 0.12mm]
The wires each have a diameter of 2 cm, length of 6 m, and aremade from a material with modulus of elasticity ? = 19.3 GPa.If three external loadings are applied to the rigid beam AC,determine the angle of tilt of the rigid beam. Assume thedeformation of the wires obeys the Hooke’s law
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E = 210 GN/m 2. [32, 63.7, 176.8 MN/m z, 0.062 mm.] can you please answerthis question fully and if you use * can you please tell me what you mea by it?
The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm andagagelengthof50.8mm.IfaloadofP=60kNisapplied to the specimen, determine its new diameter and length. Take n = 0.35.
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.