According to this image, what is the moment caused by the given force about point B? 1.2 m .065 N 2.1 m 3.3 m 0.078 Nm counterclockwise -0.078 Nm clockwise 0.1365 Nm counterclockwise -0.1365 Nm clockwise None of the above B

According to this image, what is the moment caused by the given force about point B? 1.2 m .065 N 2.1 m 3.3 m 0.078 Nm counterclockwise -0.078 Nm clockwise 0.1365 Nm counterclockwise -0.1365 Nm clockwise None of the above B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: I need to solve all questions and in handwriting Q3/ Find the effective interest rate per quarter at…

Q: The roof truss shown is typically used for solar energy purposes, where a near normal angle of…

Q: Some students were performing a hydraulic jump experiment using a wide channel during their…

A: Y1=0.6m Y2=3m To find the velocities and Froude numbers before and after the jump the energy…

Q: Question- A vertical photograph was taken at an altitude of 2000 m above mean sea level. If the…

A: Given- Altitude H=2000 m, Photograph elevation=250 m, Scale S=1:1000,

Q: rigid block of weight W is supported by three symmetrically spaced rods as shown in the Figure. Each…

A: To determine: a) The weight of W (kN) that can be supported by the system b) Actual stress in…

Q: Two small circular orifice of diameters d₁ and d2, respectively, are placed on the side of a tank at…

Q: A quadrilateral ABCD (violet) is subjected to axial and shear forces transforming it into a right…

A: The given figure is shown below:

Q: From the following description of the load path, where and in what direction do you think the…

A: This question is related to the Structural analysis from Civil Engineering. In this question ask…

Q: Determine for the slope at support C and B, and deflection at every 0.5m interval. Take E =…

A: As per company policy we can only first question. Kindly post other questions as seperate question.…

Q: A1 = 1 ft2 Q1 = 10 cfs P1 = 10 psi (1) (4) Find the pressure at section (3). (2) A2 = 0.07 ft2 P2 =…

A: To find velocity at section 2 Pressure at section 3 Discharge at section 4

Q: Laboratory results on a soil have shown that its unconfined compressive strength is 1.2 kg/cm2. In a…

Q: As a round log passes through a sawmill, two slabs are cut off, resulting in the cross section…

Q: 6. In the AASHTO design guides, the structural number (SN) addresses the structural capacity of: a.…

A: This question is related to the Highway Engineering from Civil Engineering. This is multiple choice…

Q: Compute

Q: E = 200 GPa 48 kN/m DA section is 8 KN Im 5130 X 15 BA

Q: ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG…

A: Given, to determine the coordinates of the centroid of the plane region shown.

Q: Determine the moment of inertia of the cross-sectional area about the z axis. Set a = 120 mm, b= 110…

Q: Determine the force in member AD for the truss shown using the method of joints. A 4 m O a. 93.75 kN…

Q: What is the total volume of concrete in CY to place a 26 ft wide, 10 in. thick PCC pavement on a…

Q: Theory of structure Drow A.F.D S.F.D B.M.D

A: Given:

Q: Q3. A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in…

Q: If P = 114 kN, determine the normal stress produced at point H of the pier support shown. P 500 mm

A: Given : P = 114 kN To find : Determine the normal stress produced at point H ?

Q: Question- Calculate the metacentric height of a rectangular floating body of length 15m, and width…

Q: Q. 6. Draw the shear and moment diagram for each of the following system: C. 200 lb/ft 6 ft 2 kip/ft…

A: Note: As per bartleby guidelines, only 1st 3 subparts need to be solved. For rest of the subparts ,…

Q: Given: g1 = - 2% == g2 = + 3% BVC Station = 16+50 BVC Elevation = 112.00' L = 400.00' What is the…

A: The answer is 18+10.

Q: 1. A soil sample is collected at 20 °C and taken to the laboratory. The sample is in a stainless…

A: A soil sample in stainless steel cylinder is given with the weight of the cylinder and weight of…

Q: Working on discharge and peak flow for hydrology. I did some data analysis and need to know what is…

A: Given: The average depth of runoff produced across the basis and the measure of flashiness has been…

Q: Calculate the shape factor and fully plastic moment M, of the section shown in above figure. Assume…

Q: The Howe truss is subjected to the loading shown. Determine the support reaction forces and the…

Q: An I-beam having a cross section shown below, determine the y from the x-axis shown. Calculate the…

A: Given d= 330 mm tf1= 10 mm tf2= 11 mm b1= 220 mm b2= 240 mm tw= 9 mm

Q: Calculate the diameter of a pipe that would carry 75.0 ft/s of a liquid at an average velocity of…

Q: Determine the reaction at A for the beam shown below. 3m O a. Ay = 246 kN ↓ O b. Ay = 148 kN ↓ O c.…

Q: Assume F₁ = 40 kN, F₂ = 50 kN, F3 = 15 kN, F4 = 50 kN, and M = 130 kN.m. 6 m H F 8 m B C M D x F₂

Q: Problem 11.4 - Determine the product moment of inertia of the beam's area with respect to axes…

Q: 2. The AASHO present serviceability rating (PSR) was considered an objective quantity used to…

A: Question) The AASHO present serviceability rating (PSR) was considered an objective quantity used…

Q: Gasoline has a specific weight of 42.5 lb/ft³, flows in a pipe enlargement from 2.05 in. iameter to…

A: D1=2.05in D2=3.71in To find velocity v1

Q: The wide-flange beam shown in Fig. is strengthened by bolting two cover plates 160 mm by 20 mm to…

A: Given data : This is a problem of Structure. To Find : a) Total force in each cover plate b)…

Q: A triangle inscribed in a semi-cirice with radius r shown below. Locate the centroid from point O.…

Q: Q1. Find the horizontal thrust of the water on each foot of width of the sluice gate, given y₁ = 7…

Q: The following data were obtained by conducting liquid limit and plastic li tests on a soil collected…

A: To determine: a) Draw the flow curve and determine the liquid limit b) Using the Casagrande…

Q: Find

Q: Air at standard conditions flows over a flat plate. The free stream speed is 3 m/s. What is the…

A: Given : Stream speed = 3 m/s Kinematic viscosity of air = 1.5 X 10-5 m2/s Density = 1.23 kg/m3 To…

Q: 2. Construct the influence line diagram for the bar force in member HK of the truss shown. Determine…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Problem 4. Determine the maximum deflection and slope.

Q: 6. A tertiary treatment plant treats a municipal secondary effluent and is to employ fixed-bed…

A: Reference : Environmental Engineering, Waste water treatment plant. Given : Flow, COD, Contact time…

Q: On a railway track with rail lengths of 12.8m sufficient depth of ballast needs to be provided.…

A: Given- Rail lengths L= 12.8 m, Sleeper density = n+7, Width of the sleepers = 25cm, It is needed to…

Q: Consider the beam shown in (Figure 1). EI is constant. Use the conjugate-beam method. Suppose that M…

Q: What is Go? And where did that 0.29 come from?

A: This question is related to the Fluid Mechanics from Civil Engineering. This is combined problem…

Q: ons at supports shear and moment diagrams. EI is constant. 12 kip Fhed -6 ft- B 6 ft- -12 ft- and 3…

Q: 5-pound chain assumed to be 100 feet long was supported at both ends under a 12 pounds pull. what is…

A: error due to sag = WPm2×Lo24=5122×10024=0.7233 ft

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

According to this image, what is the moment caused by the given force
about point B?
1.2 m
.065 N
2.1 m
3.3 m
0.078 Nm counterclockwise
-0.078 Nm clockwise
0.1365 Nm counterclockwise
-0.1365 Nm clockwise
None of the above
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

20. What is the maximum value of moment at D in KN-m?
How to solve for the shear and moment diagram Wu = 250 kN/m
If the equivalent single force of the system is 300 kN acting up along the y-axis, determine the magnitude and direction of F2 and its direction if F3=255 N and F1=477.44 N and α=60°.
What is the general moment equation? Section the beam at the rightmost segment of the beam. El = 75,000 kN∙m2
22. What is the maximum value of moment at C in KN-m?
Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent couple moment (Nm) acting at O if P = 507 N , Q = 382 N, and T = 451 N . Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of moment: use CW if clockwise , CCW if counterclockwise.
The C200×20 channel section of Figure P4.5 has second moments of area Ix =15×10^6 mm4, Iy=0.637×10^6 mm4. It is loaded by the bending moments Mx=2200Nm and My =−350 Nm. Find the magnitude and location of the maximum tensilestress in the beam.
Determine the Magnitude and Direction of the resultant in KN of a concurrent forces as follow: 230 Kn at 30degree from +x - axis ; 400Kn at 135degree from +x - axis; and 300Kn at 210degree from +x - axis. ANSWER: 423.549
Determine the solution for the bar forces in the truss shown when P = 1 kip and x = 5 ft: AC = -1732.05 AB = 2000 BC = -866.03 BD = 2500 DC = 2020.73 EC = -3175.43
At what angle theta must the 400N force be applied in order that the resultant R of the two forces have a magnitude of 1000N? For this condition what will be the angle beta between R and the horizontal
. Given that T = 7979 kN and W = 8080 kN, determine the total moment produced at point B by the two forces.
Determine the magnitude of the resultant moment (Nm) produced by forces P = 661 N and Q = 366 N about point O. Round off only on the final answer expressed in 3 decimal places.