Determine the moment of inertia of the cross-sectional area about the z axis. Set a = 120 mm, b= 110 mm, d = 20 mm, h=180 mm.(Eigure 1)Express your answer with the appropriate units.1₂= 11022857.14 mmμA 3 ➜ CSubmit Previous Answers Request AnswerFigureX Incorrect; Try Again; 4 attempts remainingh?1 of 1

Given Diagram: To Find:moment of inertia of the cross-sectional area about the…

Determine the moment of inertia of the cross-sectional area about the z axis. Set a = 120 mm, b= 110 mm, d = 20 mm, h 180 mm (Figure 1) Express your answer with the appropriate units. O HA 1 C 1, 11022857.14 mm Figure Submit Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining 1 of 1

Determine the moment of inertia of the cross-sectional area about the z axis. Set a = 120 mm, b= 110 mm, d = 20 mm, h 180 mm (Figure 1) Express your answer with the appropriate units. O HA 1 C 1, 11022857.14 mm Figure Submit Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining 1 of 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
Pitot PipeBy connecting a mercury pressure gauge to a vertical pipeline through which water is transmitted, speed measurement is performed with a pitot tube. Since the deviation from the pressure gauge column is 15 cm, calculate the speed of the water in the pipe. (Pmercury=13560 kg/m3, Pwater=1000 kg/m3) (Answer is V2=6.08 m/s)
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
an open circular vessel is 1m in diameter and 2m in height. it contains water filled to a depth of 1.5m. if the cylinder rotates about its vertical axis, what is the pressure intensity at the center of the bottom if w= 6 radians/second? (Unit of the correct answer : kPa) CHOICES a.) 12.465 b.) 21.456 c.) 16.425 d.) 15.542
A wooden block (40 cm wide (b), 20 cm long (h) and 15 cm deep) floats on the seawater (specific gravity, sg = 1.025) with a depth of immersion is 12 cm. Calculate the position of metacentre, MG and justify the stability of block with the aid of sketch.
Compute the gage pressure of a gas having an absolute pressure of 40 psia and the atmospheric pressure of 846 mbar, (note: 1bar=100kPa). Note: Use 1kg = 2.205lb Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: psi (lb/in2) Decimal Places required in the final answer: 3
answers should be in 3 decimal places The rotation of a flywheel is defined by the rotation ω = 2(4t + 1)1/2, where ω is in rad/sec and t in sec. When t =0, θ = 4 rads. 1. Find the value of θ when t = 5 secs. 2. Find the value of α when t = 5 secs.
flow of water in the below diagram is from point X to Y. The oil is in the e inverted U-tube manometer. The mercury is in the bottom of the manome ressure difference P -P in kPa?
A ball is thrown straight upward from the ground level. Its initial velocity is 30 m/s. 1. What is the maximum height it reaches in meters? a. 13.98 b. 45.87 c. 10.38 d. None of these 2. What is the total time in seconds when it goes back in the ground? a. 3 b. 6 c. 4 d. None of these
A venturi meter with 150 mm diameter at inlet and 100 mm at throat is laid with its axis horizontal and is used for measuring the flow of oil of sp. gr. 0.9. The oil mercury differential manometer shows a gauge difference of 200 mm. Calculate the discharge in liters/s. Assume the co-efficient of meter as 0.98. a. 56.4 b. 25.7 c. 27.8 d. 63.93
Two pipes, each 300m long 300 , are connected in series. The flow of water through the pipes is 150 L/s 0.15 with a total friction loss of 15m 15. If one pipe has a diameter of 300mm 0.3, what is the diameter of the other pipe? Neglect minor losses and assume f=0.02 0.02 for both pipes. Express your answers in 3 decimal places.