Add/Sub the following rational functions. SHOW YOUR WORK IN THE ANSWER BOX x + 2 x + 5 x2 + 6x +5 2]

Q: Problem 1: The van shown in the photo has a mass of 2500 kg and the trailer has a mass of 800 kg. Th...

A: Draw the FBD of the given system showing all forces along their correct directions and then apply Ne...

Q: mpute the required section modulus Z of a steel beam 5.0 m between simple supports and will carrying...

A: Concrete weight =30kNm3udl=30kNm3×0.11m×1m=3.3kNmBeam weight =0.5kNmso,Total weight =3.8kNmMax momen...

Q: A 7.5 m long simple span beam as shown below supports a deadload and liveload throughout its entire ...

A: The bending moment calculated from factored loads is called factored moment. Factored load, W=1.5DL+...

Q: The figure below shows a bracket plate to transmit a reaction of 150 kN at an eccentricity of 95 mm ...

A:

Q: Determine static indeterminacy of truss

A: This question is related with structural analysis . In this question we are provided with value of n...

Q: While you can see, the concrete seems to be dry as it is being laid out as a slab. a) What may happe...

A: a) When water is sprayed before the concrete sets, the water-cement ratio rises. 

Q: Determine the direct runoff, the D-index, and the excess rainfall hyetograph for the storm given bel...

A: DRH=Direct runoff hydrograph we have to determine ϕ-index here and excess rainfall for the hyetograp...

Q: What will be the strength of 20 mm diameter bolt of grade 4.6 (in kN) for the double cover butt join...

A:

Q: 5. A building design has spiral reinforced concrete column 9 meters high with a general cross sectio...

A:

Q: The network of a small construction project awarded to a contractor is shown in the following figure...

A:

Q: Consider the tension member shown below. The channel is made of ASTM A572 (Fy ksi; Fu = 65 ksi), and...

A:

Q: An ascending grade of 4.9% intersects another grade at STA 12+598 whose elevation is 500m. The chang...

A:

Q: Explain briefly why the result of a single row instantaneous blast would be a poorly broken burden t...

A:  For defining the term SPACING  herein the arrangements of blast holes denote the lateral distance o...

Q: A freeway is being designed for a location in mountainous terrain. The expected free-flow speed is 5...

A:

Q: PROBLEM 1(USING CONJUGATE BEAM METHOD) DETERMINE THE DEFLECTION AT POINTSB AND D 2.5 k/ft Hinge 35 k...

A:

Q: Given data : Force%3D3 N Work done=18 Joule Determine displacement

A:

Q: Find static indeterminacy for all structures please. Ns, Nse(exterior), Nsi(interior)

A: Given data in question  Trusses To find out  external static indeterminacy  Internal static indeterm...

Q: What will be thickness of base plate (in mm) required for a column ISHB 200 carrying an axial factor...

A:

Q: A bar ABCD has a circular cross section of 75 mm diameter over half its length and 50 mm diameter ov...

A: Torsion is the twisting of an item caused by an applied torque in solid mechanics. Torsion is measur...

Q: What are specific applications of engineering drawing for your discipline?

A: Engineering drawing gives information about the geometric features of any structure. It is very help...

Q: Using the following soil data (dense sand): γsoil = 18 kN/m3 γsub = 10 kN/m3 c = 12 kPa Nc = 17.69 ...

A:

Q: Problem 8 - 11 A trapezoidal flume with side slope of 1:1 carries 225 ft/s of water at a mean veloci...

A:

Q: Select all true statements. Blasting in hard rocks (vs. soft rocks) ... 1-Utilizes heave energy more...

A: Select all true statements. Blasting in hard rocks (vs. soft rocks) ...1-Utilizes heave energy more ...

Q: 4.10 PROBLEMS 4.1 Calculate the maximum axial load below. Materials are, C20 and materials. (a) Sect...

A: Given Data; 400*400 for both sections.

Q: 3. Using Virtual Work, solve for the maximum PLL that a W 21x57 beam with a simple span length of 11...

A:

Q: There are five (5) types of road classification in Malaysia. You shall generally describe the type o...

A: Road development has been underway in Malaysia since before the country's independence. Before 1957,...

Q: A bar having a radius equal to 0.375 inches is subjected to different torques along its span as show...

A:

Q: 5. The lost ABCD is a closed traverse(clockwise) in the form of square. If the bearing of line AB is...

A:

Q: A column is subjected to a load through a bracket as shown in the figure. P = 15 kN 20 cm 12 cm 12 c...

A: Given data, The resultant force in the bolt 1 is  

Q: posite open channel of varying roughness ng roughness coefficient (ne) The vertical and slantıng sid...

A: According to given data 

Q: determine the force in each member of the truss and state if the members are in tension or compressi...

A:

Q: A trapezoidal flume with side slope of 1:1 carries 225 ft/s of water at a mean velocity of 3 ft/s. T...

A: The given data is as follows: Side slope=1:1Discharge=225 ft3/secMean velocity=3 ft/sSlope of canal=...

Q: A vehicle is travelling at a speed of 120km/hrs on a roadway segment with 2% upgrade. After the driv...

A:

Q: 5. In five years P18,000 will be bedded to pay for a building renovation. In order to generate this ...

A:

Q: The beam AB supports two concentrated loads and rests on soil that exerts a linearly distributed upw...

A:

Q: A 72 cm3 sample of moist soil weights 141.5 g. When it is dried out in an oven, it weighs 122.7 g. T...

A:

Q: Thẻ back sight taken on a B.M. (R.L. 500.000m) was 3.415 m. The fore sight taken on the next point (...

A: The given question is related with surveying . In this question we are provided with value of reduce...

Q: S AREA MEASUREMENTS N W E AREA BY DOUBLE MERIDIAN DISTANCE (DMD) Problem 1: In the tabulation are gi...

A:

Q: A sag vertical curve is to be designed to join a -1.75 grade to a 3.00% grade. Assuming a decelerati...

A: According to given data  A sag vertical curve is to be designed to join a -1.75 grade to a 3.00 % gr...

Q: 15 kN/m Hinge 2 m 3 m 1 m

A:

Q: USING AREA-MOMENT METHOD: a. Determine the deflection at point B & C. Indicate its direction (↑↓) b....

A: Area-moment method- it is a type of graphical solution that provides the relation between the deflec...

Q: What will be the design bending strength for a laterally supported beam ISMB 300 of plastic section?...

A:

Q: The back sight taken on a B.M. = 500.000m) was 3.415 m. The fore sight taken on the next point (a) w...

A: Given, R.L  of benchmark, = 500 m Backsight distance = 3.415 Foresight distance = 2.125 m R.L of poi...

Q: What will be the strength of 20 mm diameter bolt of grade 4.6 (in kN) for the double cover butt join...

A:

Q: Determine the value of EI8 under each concentrated load. 500 N 800 N 2 m 2 m 1 m R1 R2

A:

Q: PROBLEM 2 (USING VIRTUAL WORK METHOD) DETERMINE THE DEFLECTION AT POINTS B AND C. El=50.0x10³ kN-m² ...

A:

Q: What will be the tensile strength due to rupture of critical section of an angle section ISA 150 x 1...

A:

Q: Using LRFD and A-50 steel, determine the maximum load Pu that the system below can carry. Assume wel...

A:

Q: From the beam shown below: Compute for the Reactions and Draw the Shear and Moment Diagram under the...

A: Compute for the Reactions and Draw the Shear and Moment Diagram under the Beam

Q: Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wren...

A: Consider the figure,

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.