The beam AB supports two concentrated loads and rests on soil that exerts a linearly distributed upward load as shown. Determine the values of Wg and wg corresponding to equilibrium if F2= 37 kN. (Round the final answer to two decimal places.) 24 kN F2 0.3 m a = 0.6 m WB 1.8 m kN/m. The value of WA is The value of wBis kN/m.

The beam AB supports two concentrated loads and rests on soil that exerts a linearly distributed upward load as shown. Determine the values of Wg and wg corresponding to equilibrium if F2= 37 kN. (Round the final answer to two decimal places.) 24 kN F2 0.3 m a = 0.6 m WB 1.8 m kN/m. The value of WA is The value of wBis kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
The cantilever beam shown is subjected to a couple and 2 forces shown. Replace these couple and forces with an equivalent couple M and single force F at point A. Show solution to the answer FH = 1.64 kN, R Fv = 1.16 kN, D M = 2.22 kN-m, CCW
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ, compression bars As’ = 2-28 mmØ, d’ = 60 mm. Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa. a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN
With the following rectangular tied column properties, check the adequacy of the biaxial column. Column Properties: b = 1.20 m h = 0.40 m d' = 0.06 m As = 3080 sq.mm. As' = 3080 sq.mm. Factored Loads: Pu = 1500 kN Mux = 300 kN·m Muy = 300 kN·m f'c = 20 MPa fy = 300 MPa
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
A cantilever beam 5 m long carries a concentrated load P at 3.75 m from the fixed end. ( E = 25 x 103 MPa, I = 1.6 x 109 mm4, P = 150 KN) What is the deflection under the load P? What is the maximum beam deflection? What is the upward force applied at the free end to prevent the beam from deflecting?
Question 3 5 pts What is the larger vertical reaction of a 6- m simply-supported beam carryinga triangular load which varies from 0 at one support and 15 kN/m at the other support? (Answer must be in kN.)
Step 2 1st condition Bending moment at hinge D =0 Rc*2 = (3*2)*(2/2) Rc = 3 KN Rc = 3 KN (upward) could you explain where these numbers coming? Why that divided by two? and is formula like this: 3kN/m*2m*2m/2m? 2nd condition Bending moment at hinge F =0 RB*2= (3*4)*(3+4/2)-3*7 RB = 19.5 KN RB = 19.5 KN ( upward) Same this formula If you can explain this like drawing this on paper and write where all meters and number come, that would be help me. If you could also tell the direction, where you would calculation them
An overhanging beam supports the loads as shown in the figure. If El 3000.65 kNm², determine the value of deflection at point Fin millimeters.
A simply-supported beam, 9 m in length, pin at A, roller at B and midspan at C, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. a. Determine the tangential deviation of C wrt B. b. Determine the tangential deviation of A wrt B.
The beam is 7m long with EI = 200MNm^2 Let P = 10 kN Find: 1. Slope at 2m from A. 2. Deflection at 2m from A.