Complete the following questionJANNAF tables.Calculate the adiabatic flame temperature (Tad) of stoichiometricH₂/0₂ system, initially at 298.15 K, assuming H₂ + O2 → H₂O(g).using the Adiabatic Chemical System (4)Calculate the adiabatic flame temperature ofstoichiometric H₂/0₂ system, initially at 298.15 K,assuming H₂ +0₂ → H₂O(g).ΣN₁2H{(T2; T°) - ΣN₁,₁H{ (T₁; T°) = ΣN,₁,H? (T°) - ΣN₁,2Hf (T°)a HP .⇒ T₂ = Tad = ?

Answered: Image /qna-images/answer/c681675b-6734-49bf-99f8-a2f81199ec5f.jpg

Adiabatic Chemical System (4) Calculate the adiabatic flame temperature of stoichiometric H₂/0₂ system, initially at 298.15 K, assuming H₂ +0₂ → H₂O(g). ΣN₁2H{(T2;T°) - ΣN₁1H{(T₁;T°) = ΣN,₁,H? (T°) - ΣN₁2H? (T°) ⇒ T₂ = Tad = ?

Adiabatic Chemical System (4) Calculate the adiabatic flame temperature of stoichiometric H₂/0₂ system, initially at 298.15 K, assuming H₂ +0₂ → H₂O(g). ΣN₁2H{(T2;T°) - ΣN₁1H{(T₁;T°) = ΣN,₁,H? (T°) - ΣN₁2H? (T°) ⇒ T₂ = Tad = ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Consider the tractor shown in (Figure 1). The front wheels are free to roll. The tractor weighs 5200…

A: Here we will use the simple equilibrium equations.

Q: Q1) Air enters a 40-cm-diameter cooling section at 1 atm, 32°C, and 30 percent relative humidity at…

Q: If you are trying to balance a seesaw and you have a higher mass on the left, should the mass on the…

Q: A thin rod of mass 100m and length L is suspended vertically and initially at rest when it is struck…

A: The mass of rod is .The mass of bullet is .The speed of bullet is

Q: In matlab code

A: The objective of the question is to determine the spring constant 'k' by fitting a straight line to…

Q: Q-63: At a point, the stress components are: 0x = 600 dy = 300 Txy = 500 Tyz = 400 %₂ = 900 Txz=-200…

Q: 1) Curve fitting Data from an experiment to estimate a spring constant k. The mass measured in grams…

Q: An adiabatic turbine receives 2.0 kg/s of superheated steam at 2.5 MPa, and 700°C. The discharge at…

Q: A convergence-divergence nozzle is a nozzle attached to a diffuser where the connection is called…

A: To Find:The temperature of the air at the throat.The throat area of the nozzle.The temperature at…

Q: Air is exhausted from the fixed jet engine at 20 kg/s with a velocity of 420 m/s while it is being…

Q: 9-102. The elevated water storage tank has a conical top and hemispherical bottom and is fabricated…

Q: 8.7 Diffuser A jet flies at an altitude of 10 km, where the pressure is 0.32 bar, and the…

A: To Find:The mass flows into the engine.The pressure increase across the diffuser.Given:The altitude…

Q: a 1 3/4 inch diameter shaft supported by two sleeve bearings, the total load on the two bearings is…

A: Given Data

Q: *6-22. Determine the force P needed to hold the 20-lb- block in equilibrium. C B A

A: Given : The weight of the block is There are three pulley A,B and C.

Q: A1. Produce a Mohr's circle for the stress state of a 2D plane stress element at position C (located…

Q: has part B of this problem been done

A: using the Euler's first law for rotation, the reaction force at each bearing is,

Q: can you do the SF and BM calculation with explanations

Q: A Ox 30% B Txy бу

A: Given Data:The value of The inclination of plane AB with the y-plane is The inclination of the AB…

Q: 700 N B 8m 500 N/m 1200 N.m 300 N CO E 3

A: For the following structure, determine the internal forces at the midpoint between B and C. Angle…

Q: WHEN SEAWATER FLOWS INTO THE BOTTOM OPENING AT 10 M/S, CALCULATE THE VELOCITY OF THE SEAWATER LEVEL…

A: The objective of this question is to calculate the velocity of the seawater level inside the ballast…

Q: m₂ + m₂ 2 - m₂ 2 3 2 m₂ 2 m₂ с {x} + [ C c]{*}+[(* m₂ = 1kg m₂ = 2kg k₁ = K₂ =k₂ = 1%/m W1₂…

A: Also,

Q: 4. To reduce recoil, many modern rifles are equipped with a recoil mechanism. That is, the portion…

A: mass of the bullet, mb = 15 g = 0.015 kgmass of the carriage, mc = 1.5 kgThe bullet's muzzle…

Q: Determine the speed of block in Q1 when it moves 2m up the slope using the Work and Energy method…

A: Given:To find:(a) Speed of the block.(b) Power of force P.

Q: d.N A fatigue crack growth test is being carried out on a large steel plate containing a 2 mm edge…

A: To find:How long will the crack grow after 10 hours? Given data:The initial length of the edge crack…

Q: Consider the gas-phase reaction for the synthesis of methanol from CO and O₂: CO + 2H₂ CH3OH. The…

A: Gas phase reaction of methanol :Kp at 500K =

Q: A source produces independent symbols from an alphabet of three letters. Each source symbols can be…

A: Probabilities,PA = 0.5PB = 0.25PC = 0.25

Q: Calculate the compressive strength for a ceramic containing crack of size100 µm. Let μ be the…

Q: Consider an elastic string of length 6 whose ends are held fixed. the string is set in motion with…

A: Given:To find:

Q: 12-31. The shaft is made of steel and has a diameter of 15 mm. Determine its maximum deflection. The…

A: The shaft is made of steel and has a diameter of d= 15 mm. Determine its maximum deflection.The…

Q: The momentum equations for a rotating shallow homogeneous fluid with a free upper surface (i.e. the…

Q: DO H a ↓ a E Data: a = 1m a B 2 P + F a a + C a G 2 a 2 a The figure above shows a truss that is…

A: The figure above shows a truss that is affected by two known external forces (P = 5 kN).Calculate…

Q: A 60,000 ft2 building used 850,000 kWh of electricity and 900 Mcf of natural gas over the past 12…

A: Given:The area of the building is the energy consumed by the building due to electricity for one…

Q: Determine the specific enthalpy (h) of a gas (PG model: k = 1.4, R= 4.12 kJ/kg-K) given u=5001 kJ/kg…

A: Given data:- The internal energy The gas constant The…

Q: Figure 1 shows a pumpjack operating at an oil well. Its representation as a linkage is also shown in…

A: Given:To find:

Q: An insulated, rigid vessel is initially empty (evacuated). However, it is connected to a steam line…

Q: A 10-kg homogeneous sphere S is fastened to the end of the 20-kg homogeneous rod OA as shown. The…

Q: The internal loadings at a section of the beam consist of an axial force of F = 380 N, a shear force…

A: Given data:The internal loadings at a section of the beam consist ofan axial force of ,a shear force…

Q: Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage…

Q: (,),= 0.2 and (,), = 0.55. At the instant shown, a counter-clockwise moment T B. You are required…

A: Given:To find:

Q: A fluid with specific weight 32 -flows through the pipe below as it narrows from a diameter of 4.8…

Q: Determine the coordinates of the centroid of the shaded area shown: 100 mm 50 mm -200 mm- 140 mm 140…

A: To determine:The coordinates of the centroid of the shaded area.

Q: 5. Water is being heated in a closed pan on top of a range while being stirred by a paddle wheel.…

Q: In the rigid rotor and elastic rotor models, comment on the differences between the expressions…

A: To Find:The differences between the expressions correspond to the frequencies of the first 5…

Q: Question 1: Saturated steam enters a converging-diverging nozzle at 1.75 MPa, 10 percent moisture,…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: For the following truss, determine by method of sections the forces in members DF, DG, and EG.…

A: For the following truss, determine by method of sections the forces in members DF, DG, and…

Q: Water is the working fluid in a Rankine cycle with reheat. Superheated vapor enters the turbine at…

A: The objective of the question is to determine the total heat addition, the percent thermal…

Q: Determine the temperature distribution in a spherical layer of a body whose inner surface of radius…

Q: 4. For the beam shown below, determine the slope and deflection at points "B" and "C". Assume E =…

A: The modulus of elasticity is .The moment of inertia is .

Q: Solve the problem using the stress transformation equations. Suppose that σx= 92 MPa, σy= 46 MPa,…

A: Given:To find:A) Determine the normal stress component acting on the plane AB.B) Determine the shear…

Q: A 2kg ball moves along a smooth circular track in the vertical plane as shown. Determine the minmun…

Question

Adiabatic Chemical System (4)
Calculate the adiabatic flame temperature of
stoichiometric H₂/0₂ system, initially at 298.15 K,
assuming H₂ +0₂ → H₂O(g).
ΣN₁2H{(T2; T°) - ΣN₁,₁H{ (T₁; T°) = ΣN,₁,H? (T°) - ΣN₁,2Hf (T°)
a HP .
⇒ T₂ = Tad = ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation of adiabatic flame temperature

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the enthalpy of combustion of propane C3H8 at 25 oC in both kJ/kg and kJ/mole under the following conditions:- 1- gaseous propane with H2O liquid in the products. 2- gaseous propane with H2O vapor in the products 3- liquid propane with H2O liquid in the products 4- liquid propane with H2O vapor in the products note: the enthalpy of evaporation of propane at 25 oC is 425 kJ/kg
In the boiler design, it is desirable to have the flue gas exit temperature above the dew point. Estimate the partial pressure of water vapor of the flue gas in kPa produced by combustion having the gravimetric analysis of: N2=71.84%, CO2=20.35% , O2=3.61%, H2O=4.20%
Liquid propane (C3H8) enters a combustion chamber at 25°C at a rate of 0.05 kg/min where it is mixed and burned with 50 percent excess air that enters the combustion chamber at 7°C. An analysis of the combustion gases reveals that all the hydrogen in the fuel burns to H2O but only 90 percent of the carbon burns to CO2, with the remaining 10 percent forming CO. If the exit temperature of the combustion gases is 1500 K, determine 1-The balanced chemical equation for the actual process 2-Air- Fuel ratio 3-The mass flow rate of air
Liquid octane is burned steadily with air in a jet engine. If the air–fuel ratio is 18 kg air/kg fuel, determine the percentage of excess air used during this process.
Identify if the property of the following steam: Pressure Specific Enthalpy Specific Entropy MPa kJ/kg kJ/kg-K 13 2483 ?
In a combustion chamber, ethane (C2H6) is burned at a rate of 8 kg/h with air that enters the combustion chamber at a rate of 176 kg/h. Determine the percentage of excess air used during this process.
A bituminous coal has the following compositions: C = 71.6 %, N2 = 1.3 %, A =9.1 %, H2 = 4.8 %, S = 3.4 %, W = 3.5 %, and O2 = 6.3 %. The dilution coefficient is 1.35and the coal consumption is 11762 kg/hr. Determine: a) the actual air-fuel ratio requiredfor combustion; and b) the actual air required per hour.
A gaseous fuel with 80% butane, 15% nitrogen and 5% oxygen (on a mole basis) is burned to completion with 120 percent theoretical air that enters the combustion chamber at 30°C and 100 kPa. Determine the volume flow rate of air required to burn fuel at a rate of 2 kg/min.
A gaseous fuel mixture has a molal analysis:H2 = 14% CH4 = 3% CO = 27%O2 = 0.6% CO2 = 4.5% N2 = 50.9%Determine the theoretical air-fuel ratio for complete combustion on molal analysis.
how do you apply the 80 percent of the exceeded air to the combustion equation, as there is a ratio of 1.8 and 0.8 in places? also explain how from the energy balance equation the Qout was obtained?
Combustion products from a burner enter a gas turbine at 10 bar and 950°C and discharge at 1.5 bar. The turbine operates adiabatically with an efficiency of 77%. Assuming the combustion products to be an ideal-gas mixture with a heat capacity of 32 J mol−1 K−1, what is the work output of the turbine per mole of gas, and what is the temperature of the gases discharging from the turbine?
Refrigerant 134a (R134a) is in vapor/liquid equilibrium at 200 K. The saturation pressure is 7.0282 bar, the enthalpy of the saturated liquid is 107.39 kJ/kg and the enthalpy of the saturated vapor is 353.06 kJ/kg. Compute the entropy of vaporization in units of kJ/(kg K). Report your answer using three decimal places.