For the following time-domain functions, plot the magnitude spectrum for 0So250 with do-0.2 and determine the peak magnitude and the cut-off frequencies fer, and feH (in Hz). Use a time inverval dt=0.001 for generating the time values and the amplitude values of x(t). -251 x(t) = 90esin(95t)u(t) x(t) = 220cos(11Ot), -0.2

For the following time-domain functions, plot the magnitude spectrum for 0So250 with do-0.2 and determine the peak magnitude and the cut-off frequencies fer, and feH (in Hz). Use a time inverval dt=0.001 for generating the time values and the amplitude values of x(t). -251 x(t) = 90esin(95t)u(t) x(t) = 220cos(11Ot), -0.2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

7- If the sampling period of a 2500 Hz sinusoidal signal is 0.1msec. then the number of samples can be found in time domain is
Find out the period of the given signal x[n]=cos(pi/3)n What will be the unit of the period?
The baudwith of amplitude modulated component is IOKAE, the aighest frequency is T05 K Hz. Find carrier frequency of AM sign9/·
Using MATLAB, plot a sine wave of angular frequency of 50 rad/s and having an amplitude of 10. Plot exactly 10 cycles of the wave. I am beginner is MATLAB. No need to explain the code. Provide me with the output graph.
what is the phase angle of iT in degrees when expressed as a cosine function?
Q2: Express each of the following functions in phase angle form and sketch the fre- quency spectrum (a) f(t)= 2+3sint- 2 sin3t – cos5t (b) f(t)=1-sint+ 2cost – cos2t + cos3t – 2 sin3t (c) f(t)= sin t cos3t
3) Find and sketch the frequency spectrum of the half-wave rectified cosine wave form in the following Figure. -8 -6 -4 -2 51014 (a) 4 6 8 10 (ms)
IN A SERIES RLC CIRCUIT DRIVEN BY SINUSOIDAL INPUT SIGNAL, THE PHASE BETWEEN THE CURRENT AND THE INPUT VOLTAGE IS PLOTTED IN THE NEXT GRAPHAT FREQUENCY OF THE DRIVING (INPUT) VOLTAGE F= 1OKHZ THE PHASE BETWEEN THE CURRENT AND THE INPUT VOLTAGE IN RADIANS IS ABOUT: 1.6 1.2 0.8 0.4 -0.4 -0.8 -1.2 -1.6 1 10 100 1000 Frequency (f), kHz O g. 0.8 O b. 0.4 O c. 1.57 O d. 3.2 O e. zero pe. (0) aseyd
5. For a 1Vpp sinusoidal input, at a frequency of 1KHz, draw the output for each circuit.
Ex: Design a noninverting summer circuit to achieve a 3 summing function for two analog signals 3 filt) = 5 Sin 2πT 10³t and f(t) = Ult). Draw the output waveform.
Q22). Find the average power of signal z(t) -3. we we aue awe 8le- -45°
Draw a square wave and point out or Label the amplitude, duty cycle, and period of the waveform. Draw a “high sweep-rate" image of a square pulse and indicate by labeling its overshoot, pulse width, rise-time and fall-time and the points on the waveform where these values are measured. Name and Draw a square wave that has a 25% duty cycle, a 1 Vpeak voltage, and a 10 mSec period.