A series circuit consists of an oscillating voltage source (@=20 rad/s), a 302 resistor and an unknown component (R, L or C in the “?" box) as shown. 7. If the voltage is observed to lead the current, identify the type of the unknown component. 8. With the emf amplitude set to 150V, the current amplitude is observed to be 3A. Find the value of the unknown component. 9. A second unknown component is added to the circuit (in series again) and the current increases to 5A (without changing the emf amplitude). Find the value of this new component.

A series circuit consists of an oscillating voltage source (@=20 rad/s), a 302 resistor and an unknown component (R, L or C in the “?" box) as shown. 7. If the voltage is observed to lead the current, identify the type of the unknown component. 8. With the emf amplitude set to 150V, the current amplitude is observed to be 3A. Find the value of the unknown component. 9. A second unknown component is added to the circuit (in series again) and the current increases to 5A (without changing the emf amplitude). Find the value of this new component.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In an AM signal that is 100 percent modulated, what maximum voltage value is present in each sideband?show solution
for the BJT circuit shown with ( β = 120) determine low cutoff frequencies and what isthe effective low cutoff frequency
If the frequency that is injected into an AM modulator is 100Mhz and it is combined with another injected signal of 10Khz, we can say that the combination is:
For a mosfet amplifier circuit, how can I choose an input and output capacitor with poles at 10Hz and 100Hz? Where RC = 1/w.
Bandwidth beta=250Hz, center frequency f0=750Hz of the band-proof circuit consisting of serial LCis desired.If the capacitor value is 100nF, what should the R and L values be?
An FM modulator has kf=30kHz/V and operates at a carrier frequency of 180 MHza. Find the output frequency for an instantaneous value of the modulating signal equal to150mV. b. If the carrier signal is modulated by a 2Vrms sine wave. Calculate the peak frequencydeviation.
Apply the knowledge gained from the ac analysis of BJT to construct the AC equivalent model of the circuit shown in Figagure and calculate Zo and Av. Given, β = ( 79 × 10) and ro = 79 kΩ
-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
Figure 1 illustrates a BJT amplifier with voltage gain of -115. a) Identify the capacitors in Figure 1, whose influences are negligible when considering the frequency response over high frequency range of > 1MHz. Explain briefly the reason. b) Identify the capacitor that needs treatment using the principle of "Miller effect capacitance". Calculate the input and output capacitances. c) Determine the upper-cut off frequency of the circuit, which is due to the output of the network only
A phase modulator has a phase deviation constant Kp = 35 degrees/V. The carrier signal is ec = 8cos2(pi)(800k)t, volts and the modulating signal is em = 5sin2(pi)(2000)t, volts. a. What is the equation of the PM signal? b. What is the maximum phase deviation? c. What is the amount of deviation in the carrier phase angle at t = 160 micro-s?
A 10 MHz TXCO is driving a receiver’s front end and has a frequency deviation of 3 ppm. It drives a direct downconversion RF front-end mixing the E5b frequency. What is the frequency offset at baseband due to the TXCO?
The following data are given for a two-branch parallel circuit: ? = 125V, ?? = 15, ?? =25 ?? = 15. For what value of ?? will the circuit be in resonance, and what will be the totalcurrent and power in this situation?