After routing cable from an existing device box through a wall and pulling the cable into a new box, your next step is to A. replace the existing receptacle with a higher-capacity device. B. apply power to the circuit. C. strip and connect the wires to the existing receptacle. D. tighten the internal cable clamps in the new box.

After routing cable from an existing device box through a wall and pulling the cable into a new box, your next step is to A. replace the existing receptacle with a higher-capacity device. B. apply power to the circuit. C. strip and connect the wires to the existing receptacle. D. tighten the internal cable clamps in the new box.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter12: Lighting Branch Circuit And Small-appliance Circuits For The Kitchen

Section: Chapter Questions

Problem 19R: a. The Code requires a minimum of two small-appliance circuits in a kitchen. Is it permitted to...

See similar textbooks

Similar questions

a. What circuit supplies the workshop lighting? ________________ b. What circuit supplies the plug-in strip over the workbench? ________________ c. What circuit supplies the freezer receptacle? ________________
A residential air-conditioning unit is installed in the attic. a. Is a lighting outlet required? __________ b. What Code section applies? __________ c. If a lighting outlet is required, how shall it be controlled? __________ d. What Code section applies? __________ e. Is a receptacle outlet required? __________ f. What Code section applies? __________
grounding and bonding requirements 17. Which of the following is effective when it comes to establishing a bonding connection between a fitting or a raceway and an enclosure? A. Meter enclosures B. Bonded bushings C. Bonding wedge D. Threaded hubs 18. Which of the following is the first line of defense for a premises wiring system served by a grounded utility source? A. The system grounding connection B. The pad-mounted transformer C. The load side of the service point D. The service equipment enclosure
Take a look at the wire supplying your house, another residential house, commercial and industrial buildings in your locality, count how many wires are connected to the building (from the electric meter to the weather head OR the service drop itself)? Are the wires different from each other? If so, why?
3. Identify and explain the safety procedures and precautions that should be followed for fire prevention and safety during the installation of the cables? Note: Please do not handwritten.
9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic cable?A. It should be polished.B. It should be broken off and thrown away.C. Connectors don't have ferrules.D. It should be roughened with sandpaper.9.b. Which type of test should be performed on an installed cable after it has been terminated?A. Bit error rate testB. Continuity testC. OTDR
Q.12 What provides branch-circuit protection, and where is it located? Select one: A. BREAKERS LOCATED IN THE SERVICE PANEL B. BREAKERS LOCATED AT THE OVERLOAD C. FUSES LOCATED IN THE BUS PLUGS D. FUSES LOCATED AT THE DISCONNECT
List the equipment in detail with rating for substation and swictchgear installation.
Please answer the question full sentence 5. Identify the minimum distance requirements between network cables and power sources and identify types and location for cable supports.
a. The Code requires a minimum of two small-appliance circuits in a kitchen. Is it permitted to connect a receptacle in a dining room to one of the kitchen small-appliance circuits? _______________ What Code section applies to this situation? _______________ b. Are outdoor weatherproof receptacles permitted to be connected to a 20-ampere small-appliance circuit? _______________ c. Receptacles located above the countertops in the kitchen must be supplied by at least _______________ 20-ampere small-appliance circuits.
True or False: Receptacles used on the job site should be protected with a GFCI.
10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50