6. Question 1Air1.5 barFoamFIC3056464M1201.5barLevelMS105PTAcidBT 650QE3022QE3023pHPO162QETE3021TEMPBaseBT 7507513022AG-123CoolingHOHLEAntifoamBT 85085130082 bar300SPA-141P.951LE3006LevelFor the associated P&ID, FIC 3056 is a Pressure Indicator and Controller.O TrueO False

p is used in that diagram as an indication of pressure for the inlet of air and O2 to control the…

Air 1.5 bar Foam FIC 3056 464 1.5bar 120 Level MS 105 Acid BT 650 QE 3022 PT 162 QE 3023 PH PO TE TEMP Base BT 750 QE 3022 AG-123 Cooling H3O 2bar LE Antifoam BT 850 3008 300 SPA-141 LE 3006 Level 951 For the associated P&ID, FIC 3056 is a Pressure Indicator and Controller. O True O False

Air 1.5 bar Foam FIC 3056 464 1.5bar 120 Level MS 105 Acid BT 650 QE 3022 PT 162 QE 3023 PH PO TE TEMP Base BT 750 QE 3022 AG-123 Cooling H3O 2bar LE Antifoam BT 850 3008 300 SPA-141 LE 3006 Level 951 For the associated P&ID, FIC 3056 is a Pressure Indicator and Controller. O True O False

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the size of a piston rod subjected to a total load of having cyclic fluctuations from 15 kN in compression to 25 kN in tension. The endurance limit is 360 MPa and yield strength is 400 MPa. Take impact factor = 1.25, factor of safety = 1.5, surface finish factor = 0.88 and stress concentration factor = 2.25.
o ; jith it. The external dig,, === 10.20. A shaft has a number of a collars integral with ey, the collars is 00 and rhef:}mﬂ diemater is 250 mm. If the intensity of pressure is (.35, 1) and the coefficient of friction is 0.05, estimate : 1. power absorbed when the shu; SPEBm. carrying q load of 150 kN« and 2, mamber of collars required. «d —ann AN e - g
1. The mean effective pressure of an engine running at 300 rpm is 500 kPa. What is the indicatedpower if the engine has bore of 250 mm x 450 mm. Select the correct answer below: A. 110.5 kW B. 150 kW C. 200 kW D. 182. 2 kW 2. In a certain process, entering is 1500 KJ/kg and 150 m/s. If the energy leaving is 12000 Kj/kg/ Determine the velocity at exit. Select the correct answer below: A.) 145 m/s B. 1020 m/s C. 789 m/s D. 978 m/s
In terms of theoretical stress concentration factor (Kt ) and fatigue stress concentration factor (kf) What is the notch sensitivity q?
A 2-cm square cross-section steel part having a Brinell hardness of 200 and a length of 5 cm is to be ground by adhesive wear using a tool of electroplated chromium with a square head of 2 mm x 2 mm. If the normal force applied is 20 kN and the depth to be removed from the surface is 4 mm, determine the number of passes needed (parallel to the length direction) for poor lubrication. Select one: O a. N = 1570 O b. N = 2093 O c.N = 6278 O d. N = 3139
A high-pressure gas cylinder contains 50.0 L of toxic gas at a pressure of 1.40×10^7 N/m^2 and a temperature of 25.0ºC . Its valve leaks after the cylinder is dropped. The cylinder is cooled to dry ice temperature (–78.5ºC) to reduce the leak rate and pressure so that it can be safely repaired. Show your work. a. What is the final pressure in the tank, assuming a negligible amount of gas leaks while being cooled and that there is no phase change? b. What is the final pressure if one-tenth of the gas escapes? c. To what temperature must the tank be cooled to reduce the pressure to 1.00 atm (assuming the gas does not change phase and that there is no leakage during cooling)? d. Does cooling the tank appear to be a practical solution?
The connecting rod of a four stroke cycle Diesel engineis of circular section and of length 550 mm. The diameter and stroke of the cylinder are 150 mm and240 mm respectively. The maximum combustion pressure is 4.7 N/mm2. Determine the diameter ofthe rod to be used, for a factor of safety of 3 with a material having a yield point of 330 MPa.Find also the maximum bending stress in the connecting rod due to whipping action if the engine runsat 1000 r.p.m. The specific weight of the material is 7800 kg/m3. [Ans. 33.2 mm ; 48 MPa]
Çift kayma gerilmesi altında çalışan ve güvenlik faktörü 5 olan bir pime aitminimum çap değerini [cm] olarak belirleyiniz. [Pim, yapı çeliğinden (structural steel)yapılmıştır ve 85 kN değerinde yükü desteklemektedir]. Of a pin operating under double shear stress and with a safety factor of 5Set the minimum diameter value in [cm]. [Pin, of structural steelbuilt and supports a load of 85 kN].
Using T = 45kN - m . (Gst - 77 GPa and Gal 27 GPa ) Evaluate Shear Stress (Maximum ) in Aluminium and shear stress (maximum) in steel.
Stress plots for (b) sigma r and theta for both the inner and outer ring. Interface pressure found to be 13.33 kpsi
In the LRT II project, steel railroad rails of 20 ?????? long are to be installed. If lowest temperature considered is ?2 ℃ and a maximum temperature of ?? ℃ is designed for, and the modulus of elasticity of steel to be ?????? ???, determine the clearance between rails such that adjoining rail will just touch at maximum design temperature.
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14