Air enters the compressor of an ideal air-standard Brayton cycle at 158 kPa, 340 K, with a volumetric flow rate of 3 m³/s. The compressor pressure ratio is 13:1. The turbine inlet temperature is 1336 K. Take the gas constant as 289 J/kg.K and Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.718 kJ/kg K respectively.

Air enters the compressor of an ideal air-standard Brayton cycle at 158 kPa, 340 K, with a volumetric flow rate of 3 m³/s. The compressor pressure ratio is 13:1. The turbine inlet temperature is 1336 K. Take the gas constant as 289 J/kg.K and Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.718 kJ/kg K respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a volumetric flow rate of 5 m³/s. The turbine inlet temperature is 1800 Κ.For a compressor pressure ratio of 6, determine:(a) the percent thermal efficiency of the cycle.(b) the back work ratio.(c) the net power developed, in kW.
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a volumetric flow rate of 5 m3/s. The turbine inlet temperature is 1800 K.For a compressor pressure ratio of 6, determine:(a) the percent thermal efficiency of the cycle.(b) the back work ratio.(c) the net power developed, in kW.
A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine drives a propeller as well as the compressor, delivering a net power of 1 MW to the propeller. Air enters the diffuser at 8000 m altitude (Ta = 236K, pa = 36 kPa) with a velocity of 550 km/h, and decelerates essentially to zero velocity. The compressor pressure ratio is 5.3 and the compressor has an isentropic efficiency of 83%. The turbine inlet temperature is 1360 K, and its isentropic efficiency is 86%. The turbine exit pressure is 10 kPa higher than the ambient pressure at that altitude. Flow through the diffuser and nozzle is isentropic. Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Using an air-standard analysis, determine: a) The mass and volumetric flow rates entering the diffuser, in kg/s and m3/s, respectively.b) The rate of heat addition to the combustor, in MW.c) The velocity at the nozzle exit, in m/s.
Air enters the compressor of an ideal air-standard Brayton cycle at 110 kPa, 289 K, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 12:1. The turbine inlet temperature is 1567 K. Take the gas constant as 289 J/kg.K and Specific heat at constant pressure and constant volume for air as 1.004 kJ/kg K and 0.708 kJ/kg K respectively. Calculate the net power developed to two decimal places and include the correct SI unit symbol.
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 305 K with a volume flow rate of 5.0 m3/s. The compressor pressure ratio is 10. At the inlet to the turbine, the temperature is 1000 K. Determine: a) The thermal efficiency, % b) The percent decrease in thermal efficiency if the efficiency of the turbine and compressor is 85%, %.
10. The initial design of an IFR turbine is to be based upon Whitfield’s procedure for optimum efficiency. The turbine is to be supplied with 2.2 kg/s of air, a stagnation pressure of 250 kPa, a stagnation temperature of 800°C, and have an output power of 450 kW. At turbine exit the static pressure is 105 kPA. Assuming for air that γ ¼ 1.33 and R ¼ 287 J/kg K, determine the valueof Whitfield’s power ratio, S, and the total-to-static efficiency of the turbine.
A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following:a. Thermal Efficiencyb. Mass flow rate, kg/min
An air standard Carnot Cycle, is executed in a close system between the temperature limits of 350K and 1250K. The pressure before and after the isothermal compression are 150kPaa and 300kPa respectively. If the net work output per cycle is 0.80kJ, determine the following: (a) mass of air (kg), (b) thermal efficiency of the cycle (%), (c) Work of compression (kJ), (d) Work of Expansion (kJ), (e) heat added in the system (kJ) and (f) heat rejected by the system (kJ).
Show a derivation of final temperature of otto cycle and diesel cycle in terms of initial temperature and ratios
A turbojet aircraft is travelling at 925 km/h in atmospheric conditions of 0.45 bar and -26oC. The compressor pressure ratio is 8, the air mass flow rate is 45kg/s, and the maximum allowable cycle temperature is 800oC. The compressor, turbine, and jet pipe stagnation isentropic efficiencies are 0.85, 0.89, and 0.9 respectively, the mechanical efficiency of the drive is 0.98, and the combustion efficiency is 0.99. Assuming a convergent propulsion nozzle, a loss of stagnation pressure in the combustion chamber of 0.2 bar, and a fuel of calorific value 43 300kJ/kg, calculate: i) The required nozzle exit are; ii) The net thrust developed; slader For a gases in the turbine & propulsion nozzle take γ = 1.333 & Cp = 1.15kj/kg.k For the combustion process assume an equivalent Cp value of 1.15 kJ/kg.k
Air enters the compressor of a gas turbine at 100 kPa and 25°C. pressure ratio 5 and For a maximum temperature of 850°C, the back work rate and thermal efficiency of the Brayton cycle Please specify.