Air flows adiabatically in a converging duct, which is fed from a large reservoir where the temperature and the pressure are 305 K and 210 kPa, respectively. At the end of the duct, where the cross-sectional area is 0.0025 m2, the pressure and temperature are 172 kPa and 278 K, respectively. Determine the Mach number at the end of the duct and find the mass flow rate.

Air flows adiabatically in a converging duct, which is fed from a large reservoir where the temperature and the pressure are 305 K and 210 kPa, respectively. At the end of the duct, where the cross-sectional area is 0.0025 m2, the pressure and temperature are 172 kPa and 278 K, respectively. Determine the Mach number at the end of the duct and find the mass flow rate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider subsonic Fanno flow of air with an inlet Mach number of 0.70. If the Mach number increases to 0.90 at the duct exit as a result of friction, will the (a) stagnation temperature T0, (b) stagnation pressure P0, and (c) entropy s of the fluid increase, decrease, or remain constant during this process?
An air stream with a Mach number of (3.04) a pressure of (302 kPa) and a temperature of (502 K) enters a diverging channel. If the ratio of the exit cross- sectional area to the inlet cross- sectional area is (3). Determine the back pressure which is necessary to produce a normal shock wave in the channel with a cross-sectional area equal to twice the inlet cross-sectional area. Assume steady, one-dimensional isentropic flow except through the normal shock wave. Ax=2Ai , Ae=3Ai
D5. A converging-diverging nozzle operates with air and subsonic flow at the inlet and supersonic flow at the outlet with no shacks inside the nozzle. Determine the mach number and static pressure at the outlet if the area of the outlet is 0.900 m2, the area of the throat is 0.490m2, and the stagnation pressure is 215 kPa.
An ideal isentropic nozzle is attached to an infinite reservoir that has stagnation conditions 3 MPa and 2250 K, and a constant specific heat of 1.2. If the nozzle's static exit pressure is 38.871 kPa, what is the exit static temperature? Also determine the nozzle's exit Mach number, stagnation pressure, and stagnation temperature.
Air flowing steadily in a nozzle experiences a normal shock at a Mach number of Ma = 2.6. If the pressure and temperature of air are 58 kPa and 270 K, respectively, upstream of the shock, calculate the pressure, temperature velocity, Mach number, and stagnation pressure downstream of the shock. Calculate the entropy changes of air and helium across the normal shock wave
An ideal gas flows through a passage that first converges and then diverges during an adiabatic, reversible, steady-flow process. For supersonic flow at the inlet, sketch the variation of pressure, velocity, and Mach number along the length of the nozzle when the Mach number at the minimum flow area is equal to unity.
A supersonic fixed-geometry inlet is operating at sea level where the temperature and pressure are 310 K and 105 kPa, respectively. The Inlet and throat cross-sectional areas are 0.133 m 2 and 0.0726 m 2 , respectively. Determine the Mach no. and mass-flow-rate for which the inlet is designed operated.
A converging–diverging nozzle receives air from a tank at 100 psia and 600°R. The pressure is 28.0 psia immediately preceding a plane shock that is located in the di- verging section. The Mach number at the exit is 0.5 and the flow rate is 10 lbm/sec. Determine: (a) The throat area. (b) The area at which the shock is located. (c) The outlet pressure required to operate the nozzle in the manner described above. (d) The outlet area. (e) The design Mach number.
Consider subsonic flow in a converging nozzle with fixed inlet conditions. What is the effect of dropping the back pressure to the critical pressure on (a) the exit velocity, (b) the exit pressure, and (c) the mass flow rate through the nozzle?
An aircraft flies with a Mach number Ma1 = 0.9 at an altitude of 7000 m where the pressure is 41.1 kPa and the temperature is 242.7 K. The diffuser at the engine inlet has an exit Mach number of Ma2 = 0.3. For a mass flow rate of 50 kg/s, determine the static pressure rise across the diffuser and the exit area
1)Air is supplied to a converging nozzle from a large reservoir where the temperature and pressure are 400 Kand 150 kPa, respectively. At a certain cross-section where the area Is 0.01 m2, the pressure and velocity are 100 kPa and 120 ms·', respectively. Assuming adiabatic flow, find the Mach number at this cross-section and determine the mass flow rate. 2) Helium flows adiabatically through a duct. At some section, where the area is 0.02 m2, the velocity is 500 ms·1 and the pressure is 100 kPa. Find the Mach number at the given section, and determine the mass flow rate if the stagnation temperature is 300 K
Mach number at a certain section in a diverging part of a c-d nozzle is 0.7. At farther section (towards the exit), Mach number reduces to 0.4. Hence, the cross-sectional area of the farther section is greater by