Answered: Air What force P is necessary to keep…

Name: AirWhat force P is necessary to keep the5 m long quarter cylinder gat
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: AirWhat force P is necessary to keep the5 m long quarter cylinder gate belowin its closed position.WaterAir6 mHingeRadius = 3 matConcrete floor

Engineering

Mechanical Engineering

Air What force P is necessary to keep the 5 m long quarter cylinder gate below in its closed position. Water Air 6 m Hinge Radius = 3 nm Concrete floor

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.115P: Determine the smallest distance I) that would prevent the concrete dam from tipping about corner A....

See similar textbooks

Similar questions

Determine the smallest distance I) that would prevent the concrete dam from tipping about corner A. Use w=62.4lb/ft3 for water and c=150lb/ft3 for concrete.
Compute the surface area of the axi-symmetric domed structure.
The 280-kg, 6-m-wide rectangular gate is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate.
What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
The 100cm radius cylinder weighs 3.1 KN and rest on the bottom of a container which is 1.5 meter long. Oil and water are poured into the left and right portion of the container to the depth of 0.8m and 1.4m respectively. Find the magnitude of the horizontal and vertical components of the force which will keep the cylinder touching the container at B.
Determine the volume of the body (s=3.0) that is required to keep the gate in the position indicated in the figure. The gate is 2.40m wide and 4.2m long.
Using the figure Determine the reaction force on the smooth support at B due to the fluid pressure on the gate. The width of the gate into the page is 1.5 m and the density of the water is 1000 kg / (m3) .
Consider a heavy car submerged in water in alake with flat bottom. The driver's side door of the car is1.1 m high and 0.9 m wide, and the top edge of the door is10 m below: the water surface Determine the net forceacting on the door ( normal to its surface) and the locationof the pressure center if : (a) the car is well-sealed and itcontains air at atmospheric pressure and (b) the car is filledwith water. (Ans:102.5 kN)
Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. If the intervening passages are filled with oil and a force of PB=4.6kn is acting on B. What must be the pressure in N/m2 exerted at A?
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
A square box of side 1 m having mass 40 kg is submergend into the water. A crane used to pull the box upto the surface of the water. Determine how much tension developed into the cable of the crane.
A triangular wooden body (S=0.80) is placed in water in theposition indicated in the figure. If the width of the body is 7.0 m,determine if the same for this position is stable or not indicating themetacentric height (YM).