calculate the effective resistance of the following combination of resistance and the voltage drop across each resistance when a P.D of 60 v is applied between points A and B 32 MW 8r /с 5c 18 D w 8 B w P.D across 30and 60=2v, P.D across 180=18v, P.D across 50=20v, P.D across 80=40v P.D across 30and 60=2v, P.D across 180-18v, P.D across 50=20v, P.D across 8Q-30v P.D across 30and 60-8v, P.D across 180-18v, P.D across 50=20v, P.D across 80=40v P.D across 30and 60=2v, P.D across 180=20v, P.D across 50-20v, P.D across 80=40v O

calculate the effective resistance of the following combination of resistance and the voltage drop across each resistance when a P.D of 60 v is applied between points A and B 32 MW 8r /с 5c 18 D w 8 B w P.D across 30and 60=2v, P.D across 180=18v, P.D across 50=20v, P.D across 80=40v P.D across 30and 60=2v, P.D across 180-18v, P.D across 50=20v, P.D across 8Q-30v P.D across 30and 60-8v, P.D across 180-18v, P.D across 50=20v, P.D across 80=40v P.D across 30and 60=2v, P.D across 180=20v, P.D across 50-20v, P.D across 80=40v O

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
For most of the circuits, determine all the voltages and currents necessary this usually involves:(Eth, VR1, VR2) VB,VC,VE, VCE,VCB, IB, IC,IE, (I'C)
shfdjkfdrhnacoioeniodinopidopdnieocmixoxwmipdf.ziudSALIDUDetu The equivalent resistance of three resistors A, B and C connected in parallel is 1.5 ohms. If A is thrice of B and C is 1/4 of B. Find the equivalent resistance when the three of them are connected in series? dhffrriru9ee
Helli. I only need the last part. Plotting power vs voltage if used as a solar cell and give the definition of fill factor. Tnx
M.C.Q Q.Why the switches used in weighted resistor DAC are of single pole double throw (SPDT) type? To connect the resistance to either reference voltage or ground To connect the resistance to reference voltage To connect the resistance to output To connect the resistance to ground
I want Introducrion for ( MEASUREMENT USING DC BRIDGES ) by using Resistance Measurement using DC Bridges , Resistance Measurement using the Wheatstone Bridges and Resistance Measurement using the Kelvin Doubles Bridges ) please write the introduction in print font to copy it ?
In the figure is shown a battery having an emf of 12 Volts and an internal resistance of 0.40 Ohm.A resistor R1 of 2.6 Ohms is connected across itsterminals ab. Determine (a) resistance of Rwhich, when connected across terminals ab inparallel with R1 will make the powerdelivered by the battery a maximum; (b)current in R1 and R; (c) terminal voltage ofbattery; (d) power in R1 and in R; (e) power lost in batteryHint: To maximize power in R, use differentiation In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of tworesistors, one is 30-Ohm and the other is R beingunknown. Determine the value of R if: (a) thepower dissipated in 6-Ohm resistor is equal tothe power in the parallel combination; (b) hepower in 6-Ohm is equal to the power of in R; (c)value of R maximum power transfer.Hint: To maximize power in R, use differentiation
What is the voltage across the 50 Ohm and 5 Ohm resistors? Using the loop hole equation, what is the voltage across the R1? What is R1?
What is the voltage reading of poins A and B; B and C; A and D; D and C; F and E? What is the current reading of poins A and B; B and C; A and D; D and C; F and A? What is the Calculated resistance of poins A and B; B and C; A and D; D and C; F and A; F and E?
9. What is the minimum ampacity of the wire that can be used for a 30A branch circuit? a. 30A b. 20A c. 25A d. 40A
What happens to the terminal voltage of the 12.0-V emf with an internal resistance of 0.150 ohm that was originally connected to a 10.00-ohm load and was replaced by a 0.500-ohm load?.
Two strain gauges are mounted so that they sense axial strain on a steel member in uniaxial tension. The 120 Ω gauges form two legs of a Wheatstone bridge and are mounted on opposite arms. For a bridge excitation voltage of 4 V and a bridge output voltage of 120 μV under load, estimate the strain in the member. What is the resistance change experienced by each gauge? The gauge factor for each of the strain gauges is 2.15 and Em for this steel is 29 × 10^6 psi.