Please solve all three parts Part B-Design of a hollow tube as a replacement for the solid shaftTo reduce cost, the manufacturer of the door handle would like to change the solid shaft AB to a hollow one If the force P and the maximum shearstress remain constant, design a hollow tube that replaces the solld one if the outer diameter is 135 mmExpress the inner radius to three significant figures and include appropriate units.> View Available Hint(s)HAValueUnitsSubmitPart C- Maximum force that the rFod can support given a maximum alowed shear stressIf the maximum allowable shear stress is Tallow 165 MPa, determine the maximum force P that can be applied to the door handle (Recall thatpiece AB is now a hollow tube)Express the maximum force to three significant figures and include appropriate units.>View Available Hintfs)HAP=ValueUnitsSubmitNext> earning Goal:A locked door handle is composed of a solid circular shaft AB with a diameter of b 101 mm and a flat plate 8C with a force P 74 N appled atpoint C as shown Let e 449 mm, d= 134 mm and e 157 mm (Treat the hande as if it were a cantilever beam.)BPart A-Maximum torsional shear stress in section m-mDetermine the maximum torsional shear stress Tmax experienced by the solid shaft in section m-m.Express the shear stress to three significant figures and include appropriate units.> View Available Hint(s)HẢValueUnitsTmaxSubmit

Answered: Image /qna-images/answer/1fa72f47-b303-41e9-9fbb-0ef29cb9a76a.jpg

aming Goal: locked door handle is composed of a solid circular shaft AB with a diameter of b 101 mm and a flat plate BC with a force P 74 N appled at oint C as shown Let c 449 mm d 134 mm, and e 157 mm (Treat the hande as if it were a cantilever beam.)

aming Goal: locked door handle is composed of a solid circular shaft AB with a diameter of b 101 mm and a flat plate BC with a force P 74 N appled at oint C as shown Let c 449 mm d 134 mm, and e 157 mm (Treat the hande as if it were a cantilever beam.)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.2P: A solid circular bar having diameter d is to be replaced by a rectangular tube having...

See similar textbooks

Similar questions

A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A plain concrete wall (i.e., a wall with no steel reinforcement) rests on a secure foundation and serves as a small dam on a creek (see figure). The height of the wall is h = 6.0 ft and the thickness of the wall is t = 1.0 ft. Determine the maximum tensile and compressive stresses o*!and trt, respectively, at the base of the wall when the water level reaches the top {d = h). Assume plain concrete has weight density ye= 145 lb/ft . Determine the maximum permissible depth dnuxof the water if there is to be no tension in the concrete.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is just taut when a roller support is added at Cat a distance s to the left of £, then the distributed load q is applied to beam segment AC, Assume E = 30 × 106 psi and neglect the self-weight of the beam and tie rod. Sec Table F-2(a) in Appendix F for the properties of the S-shape beam. (a) What value of uniform load q will, if exceeded, result in buckling of the tie rod if L1, =6 ft, s = 2 ft, H = 3 ft, and d = 0.25 in.? (b) What minimum beam moment of inertia ibis required to prevent buckling of the tie rod if q = 200 lb/ft, L1, = 6 ft, H = 3 ft, d = 0.25 in., and s = 2 ft? (c) For what distance s will the tic rod be just on the verge of buckling if q = 200 lb/ft, L1= 6 ft, M = 3 ft, and d = 0.25 in.?
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A solid circular bar having diameter d is to be replaced by a rectangular tube having cross-sectional dimensions d × 2d to the median line of the cross section (see figure). Determine the required thickness tminof the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar.
A square wood column with side dimensions b (see figure) is constructed of a structural grade of southern pine for which Fc= 10,5 MPa and E = 12 GPa. An axial force P = 200 kN acts on the column. If the dimension b = 150 mm, what is the maximum allowable lensth Lmax, of the column? If the length L = 4.0 m, what is the minimum required dimension bmin?
. A cantilever beam (width b = 3 in. and depth h = 6 in,) has a length L = 5 ft and is subjected to a point load P and a concentrated moment M = 20 kip-ft at end B. If normal stress trx= 0 at point C, located 0.5 in. below the top of the beam and 1 ft to the right of point Atfind point load P. Also show the complete state of plane stress on the element at point C.
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.