Help An 8 000-kg aluminum flagpole 100-m long is heated by the sun from atemperature of 10°C to 20°C. Find the work done in Joules by the aluminum ifthe linear expansion coefficient is 24 x 10-6 (°C)-1. (The density of aluminum is2.7 x103 kg/m³)Select one: An 800-MW electric power plant has an efficiency of 30%. It loses its waste heatin large cooling towers. Approximately how much waste heat (in MJ) isdischarged to the atmosphere per second?Select one:O a. 1 900O b. 560O c. 240O d. 1 200O e. 800

Since,you asked multiple question but we are allowed to answer one question at a time…

An 8 000-kg aluminum flagpole 100-m long is heated by the sun from a temperature of 10°C to 20°C. Find the work done in Joules by the aluminum if the linear expansion coefficient is 24 x 10-6°C)-1. (The density of aluminum is 2.7 x103 kg/m3)

An 8 000-kg aluminum flagpole 100-m long is heated by the sun from a temperature of 10°C to 20°C. Find the work done in Joules by the aluminum if the linear expansion coefficient is 24 x 10-6°C)-1. (The density of aluminum is 2.7 x103 kg/m3)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An electric wire having a mass of 0.5 kg/m along the horizontal is suspended between supports of the same elevation which is 50m apart. If the maximum tension in the wire is 800N, find a. the minimum tension b. the sag c. the length cable
FUNDAMENTALS OF DEFORMABLE BODIESThe tank shown in figure is fabricated from 10 mm steel plate. Determine the maximum longitudinal and circumferential stresses caused by an internal pressure of 1.2 MPa. Given: t = P = Required: Maximum Longitudinal Stress (σL) Maximum Circumferential Stress (σT)
Consider a wind machine designed to deliver its rated power at the average velocity fora given wind spectrum. It will be marketed for sites having wind velocity spectra thathave the same annual average velocity but with Weibull statistics ranging from k = 3/2to 5/2.a. Calculate the ratio of maximum to minimum annual average on-site wind poweravailable for exploitation for this range of wind fields.b. What additional assumptions are necessary if the power actually produced is tobe in the same ratio as in (a) above?
Two long straight current-carrying wires are lined up parallel to one another in vacuum at a distancedCurrents of I1 and flow I2 through the wires, both in the same direction generating the field of B Delta f at a midpoint between themWrite down an expression for BM in terms of the currents running in each of the wires Assume vacuum permeability u= 1
Please answer the following points in detail and rigorously. Instead ofresort to formulas, develop from basic principles (laws ofvoltages and currents, definition of electrical power, properties ofphasors, among others) d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. After, repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed by an element? Which to Q? f) Suppose you know P and Q for a two-terminal element. What is the power factor of this element? When would i be in early and when behind? g) Suppose you know the equivalent resistance R and the reactance X equivalent of a two-terminal passive network. What is the factor power of red bliss? When would I be in advance and when in backwardness?
The following data are given for a wind turbine: Blade length, l = 45 m Wind speed, U = 12 m/sec Air density, r = 1.25 kg/m3 Find the following: a) Total wind power in MW that can be extracted b) Maximum wind turbine power in MW that can be generated c) Actual wind turbine power in MW if the power coefficient is 0.38 d) Blade tip speed in m/s if the rotational speed is 7 rpm e) Tip speed ratio
A solid conductive aluminum, of conductivity or whose geometry consists of three contiguous cylinders of lengths L ,, L2 and L3, with the same axis and radii r ,, r2 and r; (see figure) is connected to a battery of voltage V, (V) through conductors of negligible resistance. Calculate: a) The resistance of the conductor. b) The current through the conductor. c) The current density. d) What is the entrainment velocity of the conduction electrons? DATA: It is assumed that each Al atom contributes 3 free electrons to the conduction process. density = 2.70 g / cm ?: MAI = 27.0 g / mol: N = 6.02-1023 atoms / mol. Elemental charge e = 1.60x10-19C
A thin insulator rod of mass m and length L=40 cm, as shown. thresholdon the surface of the plane and in an outer bend from the rails placed on the edges. It slides frictionlessly with a constant velocity of V=0,8 m/s. Itrails at the lower edge of the inclined plane. to each other with a rail parallel to the bar connected so that the bars and rails are closed, a rectangular frame they form. Rail plane is Ɵ=50° angle with horizontal plane (xz plane) is doing. Before the rod begins to weld, it must be tilted above the inclined plane. It stood above the lower edge of the plane at a distance of S=4m. Inclined plane and the rod shows a magnetic field of uniform B=0,5i+0,8j+0,20k(T) is under the influence. When the bar starts to slide, at t=3s moments the bar, the edge magnetic passing through the frame surface formed by the rails and the rails at the bottom edgewhat is flux?
Problem Description Two small metal spheres A and B have different electric potentials. Sphere A has charge qA = -6x10-6 C and sphere B has charge qB = +2x10-6 C. The radius of sphere A is 0.25 m and the radius of sphere B is 0.50 m. The two spheres are then connected with a wire. Instructions In a neat and organized fashion, write out a solution which includes the following: A sketch of the physical situation with all given physical quantities clearly labeled. If the description above consists of an initial and final state, both of these states should be represented in your sketch. Draw charge diagrams of the spheres before and after they are connected. Charges may be drawn directly on your sketches. Describe in words and mathematically what happens if you connect the spheres with a wire. Calculate the final charge on each sphere after they are connected. What assumptions did you make? Evaluate your answer to determine whether it is reasonable or not. Consider all aspects of your…
Create two problems about Steady-State Heat Flow – Heat Convection in Fluid, and write your solutions. Thank you!
A plastic ball with a mass of 2 grams is hung on a 10 cm long thin rope as in the spherical figure,a uniform electric field is applied in the + x direction. When the rope is made at an angle of 15 ° verticallyIf the ball is in equilibrium, calculate the net load (in uC) on the plastic ball.
The wires of our appliances are insulated with a material mixed with rubber, which has a very high resistivity. If a certain wire has a length of 2.5 m and the outer diameter is 5mm and its inner diameter is 0.5mm, what is its resistance? Note that the inner diameter is present to leave a hallow place where conducting wire ( usually copper) is present. Follow the format: Given: Required: Equation: Solution: Answer: