An 8-m cantilever beam has a uniformly distributed load of 12 kN.m throughout its entire length and a concentrated load denoted as P located on the free end. Determine the value of P if the flexural stress is 160 MPa. Beam's dimension is 200 mmx300 mm. O O 11 KN O 12 KN O 14 KN O 9 KN 10 KN

An 8-m cantilever beam has a uniformly distributed load of 12 kN.m throughout its entire length and a concentrated load denoted as P located on the free end. Determine the value of P if the flexural stress is 160 MPa. Beam's dimension is 200 mmx300 mm. O O 11 KN O 12 KN O 14 KN O 9 KN 10 KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.25P: An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is...

See similar textbooks

Related questions

Q: 5.104 For the machine element shown, locate the y coordinate of the cente of gravity. 50 mm 0 50 mm…

A: Given: The machine element with separate element shown by 1,2,3, and 4 is given below,

Q: If the box strikes the smooth plate, which has a weight of 21 lb and is held in position by an…

Q: A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm,…

Q: Compute the displacement done in object so that work done is said to be 124.55 J If force applied is…

A: Given data : Force applied F=30 N Work done W=124.55 J Required : Displacement

Q: Draw SFD and BMD

Q: Name the device that is used to transmit the spindle power to the workpiece when held…

A: In a lathe machine, various processes are performed on the workpieces. In the lathe, the machined3…

Q: A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn…

A: Given Data : Clicking Noise Transmission operation

Q: Compute the Strain if change in length is 0.0456 mm and original length of rod is 8 mm

A: Given data : Original length=L Change in length=∆L Required : Strain

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

Q: A machine of mass 10 kg is mounted on a vibration isolation system with THREE identical springs…

Q: Figure below shows a stress-strain diagram. Explain this curve using your own words and define…

Q: A 55-hp four-cylinder internal combustion engine is used to drive a medium-shock brick-making…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Prob. 3.6-10. The pipe-sleeve element (1) and cylindrical- rod core element (2) in Fig. P3.6-10 are…

Q: Q1/ Three reactors linked by pipes. As indicated, the rate of transfer of chemicals through each…

A: The principle of conservation of a system is represented by the mass balance equation, which states…

Q: A uniform bar of mass m= 7 kg and Length L= 1 m, pivots at point O and is supported by a spring at…

Q: The streamline passing through the distance '8' from the surface at the trailing edge passes through…

A: The solution of above question is below.

Q: Find displacement Work done=1111 J Force 111 N

A: Given data Work done (W)=1111 J Force (F)=111N

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: A closed heavy steel chamber is filled with water at 10°C and at atmospheric pressure. If the…

A: Given: Let us consider the given data, Initial temperature, T1=10°C New temperature, T2=40°C+273 To…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A: Given that: For the rod consisting of two cylindrical portions: For AB, material is steel LAB = 250…

Q: In an air conditioning system, return air at 24°C dry-bulb temperature and 40% relative humidity is…

Q: Which choices are correct explanations about the scanning electron microscope (SEM)? (Select all…

A: Given Scientific electron microscope To find Suitable statement A scientific electron microscope is…

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

A: Trusses :- Trusses are basically structures formed by joining various rods using frictionless pin…

Q: List the three types of light that may be present duringwelding.

A: Welding arcs give off radiation over a broad range of wavelengths - from 200 nm (nanometers) to…

Q: 12 m/s. 2/68 A boy throws a ball upward with a speed vo = The wind imparts a horizontal acceleration…

Q: Calculate the place remperature for a flat-plate collector whose properties are given below,…

A: Temperature of glass Tgass=50 C Temperature of wind,Twind =10 C Area=25×1= 25 mm2. Wind heat…

Q: What type of porosity is most often caused by mill scale?

A: given; What type of porosity is most often caused by mill scale?

Q: What is a Brale penetrator and what hardness scale uses it?

A: The hardness of the material is defined as the properties of being material due to which it resists…

Q: A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600°C in the boiler. It…

Q: A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and…

Q: The flow rate through a 10-cm-diameter wrought iron pipe shown below is 0.04 m³/s. Find the…

A: Given data: d=10 cmQ=0.04 m3/s Need to determine the difference in elevation (H).

Q: To predict the drag on an aircraft at a flight speed of 150 m/s, where the condition of air is such…

Q: Find displacement Work done=1111 J Force=111 N

Q: Current Attempt in Progress Determine the magnitude of the pin force at A. Assume W = 730 lb, a =…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Find the maximum shear stress in rectangular section if normal shear stress value is 22 Mpa

Q: Q2 (a) Explain the maximum Permissible speed on a curve and maximum sanctioned speed.

A: Maximum permissible speed on a curve - It is the maximum speed permitted to a train on a curve of…

Q: What forms the basis for the AWS identification systemfor nonferrous covered electrodes?

A: The welding industry has adopted the American Welding Society’s(AWS) classification number series…

Q: 6.4. A conical diverging tube is horizontal, 0.3 m long, has 75 mm throat diameter, 100 mm exit…

A: Please refer to the detailed solution given below, Answers - FX = 17.41 N FY = 17.65 N

Q: Describe an acceptable storage area for a cylinder offuel gas.

A: Storage cylinders are used for the storage of the fuel gases. These cylinders are made up of iron or…

Q: "Prob. 3.3-10. A 12-ft beam AB that weighs W, 180 lb supports an air conditioner that weighs W, =…

A: Given that: Length of the beam = 12 ft = 144 in Wa = 1000 lb, Wb = 180 lb It is required to…

Q: The cooled water from a cooling tower returns to the condenser at 21°C at a mass flow rate of 54.4…

Q: A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and…

A: GIVEN DATA- A diesel cycle given Compression ratio = 15 Polytropic index=1.1 Pressure at bottom dead…

Q: Stainless steel Iss Nuclear waste 9, w aconv T5,0 -Tsi • Constant properties • Negligible radiation…

Q: Find the applied force which produce stress of 22 N/mm2 on cross sectional area of 5.98 mm2

Q: The 2000 kg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC.…

A: Given data: Mass of concrete pipe = 2000 kg We have to determine the weight of the concrete pipe in…

Q: hy isn't anyone answering this?? A 50 lb block drops onto the top of a 25 lb spring scale. The block…

A: Given:m=50 lbms=25 lbh=6 ft =72 ink=100 lb/in

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: Find the hydraulic radius Wetted area=18.9 m2 Wetted perimeter=12.3 m

A: Given data : Wetted perimeter P=12.3 m Wetted area A=18.9 m2 To find :Hydraulic radius

Question

An 8-m cantilever beam has a uniformly
distributed load of 12 kN.m throughout
its entire length and a concentrated
load denoted as P located on the free
end. Determine the value of P if the
flexural stress is 160 MPa. Beam's
dimension is 200 mmx300 mm.
O 10 KN
O 11 KN
O 12 KN
O 14 KN
O 9 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
A simply supported beam of span 3.0 m has a cross-section 120 mm × 180 mm. If the permissible stress in the material of the beam is 10N/mm2,determine(i)maximum udl it can carry (ii) maximum concentrated load at a point 1 m from support it cancarry. Neglect moment due to self weight.
A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 7.5w N, (+)Mmax = 5.2w N-m, (-)Mmax = 4.5w N-m. From the given cross section shown, ytop = 64.183 mm, ybot = 135.817 mm, and INA = 25.059 x 10 6 mm4. The allowable stresses are as follows: σfT = 30 MPa, σfC = 60 MPa, and τ = 10 MPa. a. The safe uniform load considering tensile flexural strees is _____N/m b. The safe uniform load considering compressive flexural stress is _____ N/m. c. The moment inertia of the area about the neutral axis is _____ mm^3. d. The safe uniform load considering maximum shear force is _____ N/m e. Based on your analysis, the safe uniform load to recommend is _____ N/m.
A 25 mm wide and 100 mm deep beam is 3.4 m long. It carriesa load of 1500 kN at the middle. Determine the maximum stressdue to bending. and find the Young’s modulus of the material usedfor the beam if it is deflect 2500 mm maximum at the mid of thespan.
A simply supported beam of span 3.0 m has a cross-section 120 mm × 180 mm. If the permissible stress in the material of the beam is 10 N/mm^2, determine maximum udl it can carry.
The horizontal beam is assumed to be rigid while supporting the distributed load. Determine the angle of inclination of the beam after the load is applied. Each support consists of a wooden post with a diameter of 120 mm and an original length (unloaded) of 1.40 m- Consider E = 12 GPa
For the beam showna. Determine the maximum flexural stress P = 6kN W0 = 4 kN/m a = 8/10 m
Problem 3 only, solve carefully, include the units in every step and draw the diagram. Thanks! In a 2.5 m cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress inbeam is 120 Mpa, determine theA. section modulus, in3 B. The base and height of the beam if the base is 75% of its height, mm
A simply supported beam is subjected to alinearly varying distributed load q(x) =(x/L)q0 withmaximum intensity q0 at B. The beam has a lengthL = 4 m and rectangular cross section with a widthof 200 mm and height of 300 mm. Determine themaximum permissible value for the maximum intensity,q0, if the allowable normal stresses in tension andcompression are 120 MPa.
beam is supported by a roller and a hinge at its extremities. The 2 kN/m is loaded entirely on its 4 m length while 5 kN concentrated load is positioned 2 m from the left end of this beam. If the beam is 80 mm wide, determine the minimum height of the beam if the flexural stress is not to exceed 10 MPa.
A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 3.75w N, (++)Mmax = 2.53w N-m, (−−)Mmax = 4.5w N-m. From the given cross section shown, ytop = 100mm, ybot = 150mm, and INA = 72.92 x 10 6 mm4. The allowable stresses are as follows: σfT = 40 MPa, σfC = 70 MPa, and τ = 10 MPa. (a) The safe uniform load considering tensile flexural stress is _____ N/m. (b) The safe uniform load considering compressive flexural stress is _____ N/m. (c) The moment of the area about the neutral axis is _____ mm3. (d) The safe uniform load considering maximum shear force is _____ N/m. (e) Based on your analysis, the safe uniform load to recommend is _____ N/m
A simply supported beam of span 3.0 m has a cross-section 120 mm x 180mm. If the permissible stress in the material of the beam is 10N / mm ^ 2 determine (i)maximum udl it can carry (ii) maximum concentrated load at a point I m from support it can carry. Neglect moment due to self weight.?