Problem 3 only, solve carefully, include the units in every step and draw the diagram. Thanks!In a 2.5 m cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress inbeam is 120 Mpa, determine theA. section modulus, in3 B. The base and height of the beam if the base is 75% of its height, mm 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, findA. Force that will shear the pin, kNB. Shear pin diameter, mm2. A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa,A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA?3. In a 2.5 m cantilevered l-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress inbeam is 120 Mpa, determine theA. section modulus, in.B. The base and height of the beam if the base is 75% of its height, mm.

Answered: Image /qna-images/answer/12df5f75-cc5a-42fe-80f0-b57e44866955.jpg

olve carefully, include the units in every step and draw the diagram. Thanks! In a 2.5 m cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the A. section modulus, in3 B. The base and he

olve carefully, include the units in every step and draw the diagram. Thanks! In a 2.5 m cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the A. section modulus, in3 B. The base and he

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.17P: A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to bearing stress. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material. N = 47,
The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material. N = 47,
Two circular rods of 50mm diameter are connected by a knuckle joint, by a pin of 40 mm in diameter. If a pull of 120 kN acts at each end, find the tensile stress in the rod and shear stress in the pin.
The one end of a hollow square tube whose side is (10+N/100) in with (1+N/100) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ_all=243 ksi for pin material.N = 47,
A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile load of 150 kN. Then the tensile stress is _____________ MPa
Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ?Y=300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ?Y=300 MPa, n=2 - FOS for pin/bearing and ?Allow=300 MPa for bearing).